194 lines
7.4 KiB
Prolog
194 lines
7.4 KiB
Prolog
****************************************
|
||
* B U C K A R O O B A N Z A I *
|
||
* aka the Reset Vector *
|
||
* *
|
||
* presents *
|
||
* *
|
||
* Cracking On the IBMpc *
|
||
* Part I *
|
||
* *
|
||
****************************************
|
||
|
||
Introduction
|
||
------------
|
||
For years, I have seen cracking tutorials for the APPLE computers, but never
|
||
have I seen one for the PC. I have decided to try to write this series to help
|
||
that pirate move up a level to a crackest.
|
||
|
||
In this part, I will cover what happens with INT 13 and how most copy
|
||
protection schemes will use it. I strongly suggest a knowledge of Assembler
|
||
(M/L) and how to use DEBUG. These will be an important figure in cracking
|
||
anything.
|
||
|
||
INT-13 - An overview
|
||
--------------------
|
||
Many copy protection schemes use the disk interrupt (INT-13). INT-13 is
|
||
often use to either try to read in a illegaly formated track/sector or to
|
||
write/format a track/sector that has been damaged in some way.
|
||
|
||
INT-13 is called like any normal interupt with the assembler command INT 13
|
||
(CD 13). [AH] is used to select which command to be used, with most of the
|
||
other registers used for data.
|
||
|
||
INT-13 Cracking Collage
|
||
-----------------------
|
||
Although, INT-13 is used in almost all protection schemes, the easiest to
|
||
crack is the DOS file. Now the protected program might use INT-13 to load some
|
||
other data from a normal track/sector on a disk, so it is important to
|
||
determine which tracks/sectors are inportant to the protection scheme. I have
|
||
found the best way to do this is to use LOCKSMITH/pc (what, you don't have LS.
|
||
Contact your local pirate for it.)
|
||
|
||
Use LS to to analyze the diskette. Write down any track/sector that seems
|
||
abnormal. These track are must likely are part of the protection routine.
|
||
|
||
Now, we must enter debug. Load in the file execute a search for CD 13.
|
||
Record any address show. If no address are picked up, this mean 1 or 2 things,
|
||
the program is not copy protected (bullshit) or that the check is in an other
|
||
part of the program not yet loaded. The latter being a real bitch to find, so
|
||
I'll cover it in part II. There is another choice. The CD 13 might be hidden
|
||
in self changing code. Here is what a sector of hidden code might look like
|
||
|
||
-U CS:0000
|
||
1B00:0000 31DB XOR BX,BX
|
||
1B00:0002 8EDB MOV DS,BX
|
||
1B00:0004 BB0D00 MOV BX,000D
|
||
1B00:0007 8A07 MOV AL,[BX]
|
||
1B00:0009 3412 XOR AL,12
|
||
1B00:000B 8807 MOV [BX],AL
|
||
1B00:000D DF13 FIST WORD...
|
||
|
||
In this section of code, [AL] is set to DF at location 1B00:0007. When you
|
||
XOR DF and 12, you would get a CD(hex) for the INT opcode which is placed right
|
||
next to a 13 ie, giving you CD13 or INT- 13. This type of code cann't and will
|
||
not be found using debug's [S]earch command.
|
||
|
||
Finding Hidden INT-13s
|
||
----------------------
|
||
The way I find best to find hidden INT-13s, is to use a program called
|
||
PC-WATCH (TRAP13 works well also). This program traps the interrupts and will
|
||
print where they were called from. Once running this, you can just disassemble
|
||
around the address until you find code that look like it is setting up the disk
|
||
interupt.
|
||
|
||
An other way to decode the INT-13 is to use debug's [G]o command. Just set a
|
||
breakpoint at the address give by PC-WATCH (both programs give the return
|
||
address). Ie, -G CS:000F (see code above). When debug stops, you will have
|
||
encoded not only the INT-13 but anything else leading up to it.
|
||
|
||
What to do once you find INT-13
|
||
-------------------------------
|
||
Once you find the INT-13, the hard part for the most part is over. All that
|
||
is left to do is to fool the computer in to thinking the protection has been
|
||
found. To find out what the computer is looking for, examine the code right
|
||
after the INT-13. Look for any branches having to do with the CARRY FLAG or
|
||
any CMP to the AH register.
|
||
|
||
If a JNE or JC (etc) occurs, then [U]nassembe the address listed with the
|
||
jump. If it is a CMP then just read on.
|
||
|
||
Here you must decide if the program was looking for a protected track or just
|
||
a normal track. If it has a CMP AH,0 and it has read in a protected track, it
|
||
can be assumed that it was looking to see if the program had successfully
|
||
complete the READ/FORMAT of that track and that the disk had been copied thus
|
||
JMPing back to DOS (usually). If this is the case, Just NOP the bytes for the
|
||
CMP and the corrisponding JMP.
|
||
|
||
If the program just checked for the carry flag to be set, and it isn't, then
|
||
the program usually assumes that the disk has been copied. Examine the
|
||
following code
|
||
|
||
INT 13 <-- Read in the Sector
|
||
JC 1B00 <-- Protection found
|
||
INT 19 <-- Reboot
|
||
1B00 (rest of program)
|
||
|
||
The program carries out the INT and find an error (the illegaly formatted
|
||
sector) so the carry flag is set. The computer, at the next instruction, see
|
||
that the carry flag is set and know that the protection has not been breached.
|
||
In this case, to fool the computer, just change the "JC 1B00" to a "JMP 1B00"
|
||
thus defeating the protection scheme.
|
||
|
||
NOTE: the PROTECTION ROUTINE might be found in more than just 1 part of the
|
||
program
|
||
|
||
|
||
Handling EXE files
|
||
------------------
|
||
As we all know, Debug can read .EXE files but cannot write them. To get
|
||
around this, load and go about cracking the program as usual. When the
|
||
protection scheme has been found and tested, record (use the debug [D]ump
|
||
command) to save + & - 10 bytes of the code around the INT 13.
|
||
|
||
Exit back to dos and rename the file to a .ZAP (any extention but .EXE will
|
||
do) and reloading with debug.
|
||
|
||
Search the program for the 20+ bytes surrounding the code and record the
|
||
address found. Then just load this section and edit it like normal.
|
||
|
||
Save the file and exit back to dos. Rename it back to the .EXE file and it
|
||
should be cracked. ***NOTE: Sometimes you have to fuck around for a while to
|
||
make it work.
|
||
|
||
DISK I/O (INT-13)
|
||
-----------------
|
||
This interrupt uses the AH resister to select the function to be used. Here
|
||
is a chart describing the interrupt.
|
||
|
||
AH=0 Reset Disk
|
||
AH=1 Read the Status of the Disk
|
||
system in to AL
|
||
|
||
AL Error
|
||
----------------------------
|
||
00 - Successful
|
||
01 - Bad command given to INT
|
||
*02 - Address mark not found
|
||
03 - write attempted on write prot
|
||
*04 - request sector not found
|
||
08 - DMA overrun
|
||
09 - attempt to cross DMA boundry
|
||
*10 - bad CRC on disk read
|
||
20 - controller has failed
|
||
40 - seek operation failed
|
||
80 - attachment failed
|
||
(* denotes most used in copy protection)
|
||
AH=2 Read Sectors
|
||
|
||
input
|
||
DL = Drive number (0-3)
|
||
DH = Head number (0or1)
|
||
CH = Track number
|
||
CL = Sector number
|
||
AL = # of sectors to read
|
||
ES:BX = load address
|
||
output
|
||
AH =error number (see above)
|
||
[Carry Flag Set]
|
||
AL = # of sectors read
|
||
|
||
AH=3 Write (params. as above)
|
||
AH=4 Verify (params. as above -ES:BX)
|
||
AH=5 Format (params. as above -CL,AL
|
||
ES:BX points to format
|
||
Table)
|
||
|
||
For more infomation on INT-13 see the IBM Techinal Reference Manuals.
|
||
|
||
Comming Soon
|
||
------------
|
||
In part II, I will cover CALLs to INT-13 and INT-13 that is located in
|
||
diffrents overlays of the program
|
||
|
||
|
||
Happy Cracking.....
|
||
Buckaroo Banzai
|
||
<-------+------->
|
||
|
||
PS: This Phile can be Upload in it's
|
||
unmodified FORM ONLY.
|
||
|
||
PPS: Any suggestion, corrections, comment on this Phile are accepted and
|
||
incouraged.....
|
||
|
||
|