Since version 5.2.0 there's non-empty stop phase:
ExecStopPost=/usr/bin/env rm -f "/run/knot-resolver/control/%i"
but it's perfectly OK to run that from a different version
(and typically it's no-op anyway). Real-life example where this helps:
https://github.com/NixOS/nixpkgs/issues/49528#issuecomment-747723198
This allows to use files containing only the mpd password without the
permissions, making it easier for other programs connecting to mpd to read the
password from the same password file.
... build-vm-with-bootloader" for EFI systems
This reverts commit 20257280d9a3591a2888299a1aabfa850a0d0d08, reversing
changes made to 926a1b20949ddd66e3a4e1327cb1c1010ab10442.
It broke nixosTests.installer.simpleUefiSystemdBoot
and right now channel is lagging behing for two weeks.
This reverts commit 8f177612b14063b644288a5a1058bf47f44b43a5.
Attempting to start any service from udev when systemd-udev-settle is
used at all hangs the boot for 2min. See issue #107341.
Prior to this commit, installation over serial console would requiring
manually having to modify the kernel modeline, as described in
https://github.com/NixOS/nixpkgs/issues/58198 .
This is unnecessarily fiddly, so this commit adds a syslinux boot
entry that has serial enabled.
GRUB already has a serial console entry:
2c07a0800a/nixos/modules/installer/cd-dvd/iso-image.nix (L311-L317)
Why 115200 bps? This is already used in other places, e.g. https://github.com/NixOS/nixpkgs/pull/58196
I tested this change by building the image, booting the image, and
observing the boot process over serial:
$ cd nixos/
$ nix-build -A config.system.build.isoImage -I nixos-config=modules/installer/cd-dvd/installation-cd-minimal.nix default.nix
$ sudo cp /nix/store/arcl702c3z8xlndlvnfplq9yhixjvs9k-nixos-20.09pre-git-x86_64-linux.iso/iso/nixos-20.09pre-git-x86_64-linux.iso /dev/sdb
$ picocom -b 115200 /dev/ttyUSB0
`nixos-rebuild build-vm-with-bootloader` currently fails with the
default NixOS EFI configuration:
$ cat >configuration.nix <<EOF
{
fileSystems."/".device = "/dev/sda1";
boot.loader.systemd-boot.enable = true;
boot.loader.efi.canTouchEfiVariables = true;
}
EOF
$ nixos-rebuild build-vm-with-bootloader -I nixos-config=$PWD/configuration.nix -I nixpkgs=https://github.com/NixOS/nixpkgs/archive/nixos-20.09.tar.gz
[...]
insmod: ERROR: could not insert module /nix/store/1ibmgfr13r8b6xyn4f0wj115819f359c-linux-5.4.83/lib/modules/5.4.83/kernel/fs/efivarfs/efivarfs.ko.xz: No such device
mount: /sys/firmware/efi/efivars: mount point does not exist.
[ 1.908328] reboot: Power down
builder for '/nix/store/dx2ycclyknvibrskwmii42sgyalagjxa-nixos-boot-disk.drv' failed with exit code 32
[...]
Fix it by setting virtualisation.useEFIBoot = true in qemu-vm.nix, when
efi is needed.
And remove the now unneeded configuration in
./nixos/tests/systemd-boot.nix, since it's handled globally.
Before:
* release-20.03: successful build, unsuccessful run
* release-20.09 (and master): unsuccessful build
After:
* Successful build and run.
Fixes https://github.com/NixOS/nixpkgs/issues/107255
Fixes that `containers.<name>.extraVeths.<name>` configuration was not
always applied.
When configuring `containers.<name>.extraVeths.<name>` and not
configuring one of `containers.<name>.localAddress`, `.localAddress6`,
`.hostAddress`, `.hostAddress6` or `.hostBridge` the veth was created,
but otherwise no configuration (i.e. no ip) was applied.
nixos-container always configures the primary veth (when `.localAddress`
or `.hostAddress` is set) to be the containers default gateway, so
this fix is required to create a veth in containers that use a different
default gateway.
To test this patch configure the following container and check if the
addresses are applied:
```
containers.testveth = {
extraVeths.testveth = {
hostAddress = "192.168.13.2";
localAddress = "192.168.13.1";
};
config = {...}:{};
};
```
This means that all systems running from master will trigger
new certificate creation on next rebuild. Race conditions around
multiple account creation are fixed in #106857, not this commit.
Previously the .enable option was used to encode the condition as well,
which lead to some oddness:
- In order to encode an assertion, one had to invert it
- To disable a check, one had to mkForce it
By introducing a separate .check option this is solved because:
- It can be used to encode assertions
- Disabling is done separately with .enable option, whose default can be
overridden without a mkForce
