The original `nexus` derivation required `/run/sonatype-work/nexus3`
which explicitly depended on the NixOS path structure.
This would break `nexus` for everyone using `nixpkgs` on a non-NixOS
system, additionally the module never created `/run/sonatype-work`, so
the systemd unit created in `services.nexus` fails as well. The issue
wasn't actively known as the `nixos/nexus` test wasn't registered in
Hydra (see #40257).
This patch contains the following changes:
* Adds `tests.nexus` to `release.nix` to run the test on Hydra.
* Makes JVM parameters configurable: by default all JVM options were located
in `result/bin/nexus.vmoptions` which made it quite hard to patch
these parameters. Now it's possible to override all parameters by
running `VM_OPTS_FILE=custom-nexus.vmoptions ./result/bin/nexus run`
(after patching the `nexus` shell script), additionally it's possible
to override these parameters with `services.nexus.vmoptions`.
* Bumped Nexus from 3.5.1 to 3.11.0
* Run the `nexus` test on Hydra with `callTest` in `nixos/release.nix`,
furthermore the test checks if the UI is available on the specified
port.
* Added myself as maintainer for the NixOS test and the package to have
some more people in case of further breakage.
* Added sufficient disk space to the `nexus` test, otherwise the service
fails with the following errors:
```
com.orientechnologies.orient.core.exception.ODatabaseException: Cannot create database 'accesslog'
com.orientechnologies.orient.core.exception.OLowDiskSpaceException: Error occurred while executing
a write operation to database 'accesslog' due to limited free space on the disk (242 MB). The database
is now working in read-only mode. Please close the database (or stop OrientDB), make room on your hard
drive and then reopen the database. The minimal required space is 256 MB. Required space is now set to
256MB (you can change it by setting parameter storage.diskCache.diskFreeSpaceLimit) .
```
/cc @ironpinguin @xeji
When a package contains a directory in one of the systemd directories
(like flatpak does), it is symlinked into the *-units derivation.
Then later, the derivation will try to create the directory, which
will fail:
mkdir: cannot create directory '/nix/store/…-user-units/dbus.service.d': File exists
builder for '/nix/store/…-user-units.drv' failed with exit code 1
Closes: #33233
GRUB 2.0 supports png, jpeg and tga. This will use the image's suffix to
load the right module.
As jpeg module is named jpeg, jpg is renamed jpeg.
If the user uses wrong image suffix for an image, it wouldn't work anyway.
This will leave up to two additional left-over files in /boot/ if user switches
through all the supported file formats. The module already left the png
image if the user disabled the splash image.
If docker is enabled, start mesos-slave.service after docker.service
to avoid a race condition that could result in mesos-slave to fail
with "Failed to create docker: Timed out getting docker version"
The pull request that added dhparams (#39507) was made at the time where
the dhparams module overhaul (#39526) wasn't done yet, so it's still
using the old mechanics of the module.
As stated in the release notes:
Module implementers should not set a specific bit size in order to let
users configure it by themselves if they want to have a different bit
size than the default (2048).
An example usage of this would be:
{ config, ... }:
{
security.dhparams.params.myservice = {};
environment.etc."myservice.conf".text = ''
dhparams = ${config.security.dhparams.params.myservice.path}
'';
}
Signed-off-by: aszlig <aszlig@nix.build>
Cc: @qknight, @abbradar, @hrdinka, @leenaars
Regression introduced by d4468bedb52bf03ff125d721634f83604bddd589.
No systemd messages are shown anymore during VM test runs, which is not
very helpful if you want to find out about failures.
There is a bit of a conflict between testing and the change that
introduced the regression. While the mentioned commit makes sure that
the primary console is tty0 for virtualisation.graphics = false, our VM
tests need to have the serial console as primary console.
So in order to support both, I added a new virtualisation.qemu.consoles
option, which allows to specify those options using the module system.
The default of this option is to use the changes that were introduced
and in test-instrumentation.nix we use only the serial console the same
way as before.
For test-instrumentation.nix I didn't add a baudrate to the serial
console because I can't find a reason on top of my head why it should
need it. There also wasn't a reason stated when that was introduced in
7499e4a5b917227696b7292ae1bd728d6b1978b0.
Signed-off-by: aszlig <aszlig@nix.build>
Cc: @flokli, @dezgeg, @edolstra
