1966 lines
59 KiB
Plaintext
1966 lines
59 KiB
Plaintext
NAM Programming (Reprogramming) Instructions
|
|
|
|
For 30+ Cellular Telephones
|
|
|
|
<--Part 1-->
|
|
|
|
Presented By:
|
|
|
|
/E/D/I/S/O/N///C/A/R/T/E/R/
|
|
|
|
Of
|
|
|
|
NETWORK 23
|
|
24 HOURS
|
|
1200/2400 BAUD
|
|
(402) 467-2474
|
|
|
|
-----------------------------------------------------------------------------
|
|
PLEASE NOTE: Area specific numbers contained within these programming
|
|
instructions may not be accurate for your cellular area.
|
|
-----------------------------------------------------------------------------
|
|
|
|
Programming Instructions for:
|
|
|
|
DIAMONDTEL MESA90X HANDHELD
|
|
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
|
|
PRESS FCN 7
|
|
ENTER 4 DIGIT SECURITY CODE
|
|
ENTER NEW 3 DIGIT UNLOCK CODE
|
|
PRESS CLR
|
|
|
|
PWR up unit
|
|
Press "END" and hold within 10 seconds of pwr up
|
|
Enter "5132920"
|
|
Release END key.
|
|
|
|
0 SEND DUAL NO
|
|
|
|
XXXXXXXXXX SEND NO1
|
|
|
|
_ _ _ _ _ SEND SID1
|
|
|
|
1 SEND LU1
|
|
|
|
1 SEND EX1
|
|
|
|
334 SEND IPCH1
|
|
|
|
07 SEND ACCOLC1
|
|
|
|
0 SEND PREF1
|
|
|
|
10 SEND GIM1
|
|
|
|
0 SEND RI1
|
|
|
|
1 SEND DTX1
|
|
|
|
1 SEND AR1
|
|
|
|
1234 SEND SEC
|
|
|
|
1 SEND EE
|
|
|
|
1 SEND C TONE
|
|
|
|
0 SEND AL
|
|
|
|
0 SEND BO
|
|
|
|
1 SEND BEEP
|
|
|
|
|
|
TO EXIT PROGRAMMING MODE PRESS "END" AT ANY TIME
|
|
|
|
TO RESET NAM FROM THE LIMIT OF 3 PROGRAM ATTEMPTS
|
|
PWR up unit
|
|
Press "END" and hold within 10 seconds of pwr up
|
|
TO RESET NAM OF MESA 90 HANDHELD USE THE CODE "6972814"
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
DIAMONDTEL MESA99X HANDHELD
|
|
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
|
|
PRESS FCN 7
|
|
ENTER 4 DIGIT SECURITY CODE
|
|
ENTER NEW 3 DIGIT UNLOCK CODE
|
|
PRESS CLR
|
|
|
|
PWR up unit
|
|
Press "END" and hold within 10 seconds of pwr up
|
|
Enter "5132920"
|
|
Release END key.
|
|
|
|
0 SEND DUAL NO
|
|
|
|
XXXXXXXXXX SEND NO1
|
|
|
|
_ _ _ _ _ SEND SID1
|
|
|
|
1 SEND LU1
|
|
|
|
1 SEND MIN MARK1
|
|
|
|
334 SEND IPCH1
|
|
|
|
07 SEND ACCOLC1
|
|
|
|
10 SEND GIM1
|
|
|
|
0 SEND RI1
|
|
|
|
0 SEND DTX1
|
|
|
|
0 SEND AR1
|
|
|
|
1234 SEND SEC
|
|
|
|
1 SEND CONTINUE D.T.M.F.
|
|
|
|
0 SEND AUTO LOCK
|
|
|
|
0 SEND BOOSTER
|
|
|
|
|
|
TO EXIT PROGRAMMING MODE PRESS "END" AT ANY TIME
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
GATEWAY CP 900 HANDHELD
|
|
|
|
USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
|
|
CURRENT UNLOCK CODE CAN NOT BE SEEN AND MUST BE KNOWN TO CHANGE
|
|
THE CURRENT UNLOCK CODE.
|
|
PRESS MENU
|
|
ENTER 03
|
|
ENTER CURRENT 4 DIGIT SECURITY CODE
|
|
ENTER NEW 4 DIGIT SECURITY CODE
|
|
PHONE WILL AUTO EXIT TO READY
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
PRESS MENU 99 ENTR SCRTY CODE(FCTRY PRST IS 9999) PROGRAM NAM
|
|
|
|
_ _ _ _ _ SEND SID
|
|
|
|
XXXXXXXXXX SEND PHONE NUMBER
|
|
|
|
0334 SEND IPC
|
|
|
|
07 SEND ACCOL
|
|
|
|
10 SEND GIM
|
|
|
|
1 SEND MOBILE I.D. NUMBER
|
|
|
|
1 SEND LOCAL USE MARK
|
|
|
|
2 SEND SYSTEM SELECT (B)
|
|
|
|
UPON PRESSING SEND THE PHONE WILL CYCLE TO WAIT AND THEN RETURN TO THE
|
|
READY MODE.
|
|
|
|
TO DISPLAY THE NEW PHONE NUMBER:
|
|
|
|
PRESS RCL 00
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
GENERAL ELECTRIC MINI II
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
|
|
PRESS FCN 7
|
|
ENTER 4 DIGIT SECURITY CODE
|
|
ENTER NEW 3 DIGIT UNLOCK CODE
|
|
PRESS CLR
|
|
|
|
PWR up unit
|
|
Press and hold END key within 10 seconds of pwr up
|
|
Enter "6282905"
|
|
Release END key
|
|
|
|
0 Press SEND DUAL NO
|
|
|
|
XXXXXXXXXX Press SEND NO1
|
|
|
|
_ _ _ _ _ Press SEND SID1
|
|
|
|
1 Press SEND LU1
|
|
|
|
1 Press SEND EX1
|
|
|
|
0334 Press SEND IPCH1
|
|
|
|
07 Press SEND ACCOLC1
|
|
|
|
0 Press SEND PREF1
|
|
|
|
10 Press SEND GIM1
|
|
|
|
0 Press SEND RI1
|
|
|
|
1 Press SEND DTX1
|
|
|
|
1 Press SEND AR1
|
|
|
|
1234 Press SEND SEC
|
|
|
|
1 Press SEND EE
|
|
|
|
1 Press SEND C DTMF
|
|
|
|
0 Press SEND AL
|
|
|
|
0 Press SEND BEEP
|
|
|
|
0 Press SEND BO
|
|
|
|
|
|
TO EXIT PROGRAMMING MODE PRESS "END" AT ANY TIME
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
GENERAL ELECTRIC MINI
|
|
|
|
ACTION TO STORE DISPLAY
|
|
USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
|
|
UNLOCK CODES WILL BE CHANGED ONLY IN PROGRAMMING MODE
|
|
FOLLOW THE INSTRUCTIONS THAT FOLLOW
|
|
|
|
PWR up unit
|
|
Press and hold CL key within 10 seconds of pwr up
|
|
0Enter "7591122"
|
|
Release CL key
|
|
|
|
|
|
XXXXXXXXXX PRESS SEND MIN
|
|
|
|
123 PRESS SEND UNLOCK
|
|
|
|
_ _ _ _ _ PRESS SEND SID
|
|
|
|
1 PRESS SEND LU
|
|
|
|
1 PRESS SEND MIN MARK
|
|
|
|
334 PRESS SEND IPCH
|
|
|
|
07 PRESS SEND ACCOLC
|
|
|
|
0 PRESS SEND PS
|
|
|
|
10 PRESS SEND GIM
|
|
|
|
1 PRESS SEND EE
|
|
0 PRESS SEND BOOSTER
|
|
|
|
1 PRESS SEND AR
|
|
|
|
|
|
TO EXIT PROGRAMMING MODE PRESS "END" AT ANY TIME
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
MITSUBISHI 800
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
PWR up unit
|
|
Press and Hold STO within 10 Seconds of pwr up
|
|
Enter "5474432"
|
|
Release STO
|
|
|
|
|
|
0 Press SEND dUAL
|
|
|
|
XXXXXXXXXX Press SEND NO1
|
|
|
|
_ _ _ _ _ Press SEND SId1
|
|
|
|
1 Press SEND LU1
|
|
|
|
0 Press SEND MIN Mark
|
|
|
|
0334 Press SEND IPCH
|
|
|
|
07 Press SEND ACCOLC
|
|
|
|
0 Press SEND PS1
|
|
|
|
10 Press SEND GI1
|
|
|
|
1234 Press SEND SECUrity
|
|
|
|
1 Press SEND EE
|
|
|
|
0 Press SEND dt
|
|
|
|
1 Press SEND HF
|
|
|
|
0 Press SEND InHIbit
|
|
|
|
1 Press SEND C tOnE
|
|
|
|
0 Press SEND SyS A/B
|
|
|
|
0 Press SEND dUAL HS
|
|
|
|
0 Press SEND InHibit Ld
|
|
|
|
|
|
TO EXIT PROGRAMMING MODE PRESS "END" AT ANY TIME
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
MITSUBISHI 900
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
PWR up unit
|
|
Press and Hold END key within 10 seconds of pwr up
|
|
Enter "6972814"
|
|
Release END key
|
|
|
|
0 Press SEND DUAL NO
|
|
|
|
XXXXXXXXXX Press SEND NO1
|
|
|
|
_ _ _ _ _ Press SEND SID1
|
|
|
|
1 Press SEND LU1
|
|
|
|
0 Press SEND EX1
|
|
|
|
0334 Press SEND IPCH1
|
|
|
|
07 Press SEND ACCOLC1
|
|
|
|
0 Press SEND PREF1
|
|
|
|
10 Press SEND GIM1
|
|
|
|
0 Press SEND RI1
|
|
|
|
1 Press SEND DTX1
|
|
|
|
1 Press SEND AR1
|
|
|
|
1234 Press SEND SEC
|
|
|
|
1 Press SEND EE
|
|
|
|
1 Press SEND C DTMF
|
|
|
|
0 Press SEND AL
|
|
|
|
0 Press SEND BO
|
|
|
|
1 Press SEND BEEP
|
|
|
|
TO EXIT PROGRAMMING MODE PRESS "END" AT ANY TIME
|
|
|
|
TO ENTER TEST MODE HOLD END ON PWR UP-CODE 0944635
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
MOTOROLA 8000H
|
|
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
|
|
THIS FUNCTION IS PROVIDED IN STEP 9 OF THE PROGRAMMING
|
|
MODE
|
|
|
|
|
|
PWR up unit
|
|
Enter STORE #123456123456 RCL
|
|
If the phone is fresh from factory then
|
|
Enter STORE #000000000000 RCL
|
|
If the phone is used or already programmed then
|
|
Enter STORE #123456123456 RCL
|
|
|
|
DISPLAY WILL SHOW 01
|
|
PRESS *
|
|
|
|
_ _ _ _ _ * 02 (SID)
|
|
|
|
XXX * 03 (Area Code)
|
|
|
|
XXX XXXX * 04 (Phone #)
|
|
|
|
14 * 05
|
|
|
|
07 * 06
|
|
|
|
00 * 07
|
|
|
|
123456 * 08
|
|
|
|
123 * 09
|
|
|
|
334 * 10
|
|
|
|
010100 * 11
|
|
|
|
000 *
|
|
|
|
PRESS * TO REVIEW ENTRIES
|
|
|
|
TO BURN NAM: PRESS SEND WHILE 01,02,03, ETC. IS DISPLAYED
|
|
|
|
SET TO SCAN B MODE BY :
|
|
|
|
RCL * : PRESS * UNTIL SCAN B MODE SHOWS then:
|
|
|
|
press store
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
MOTOROLA ULTRA CLASSIC HANDHELD
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
|
|
THE UNLOCK CODE IS PROGRAMMED IN STEP 8 OF THE PROGRAMMING
|
|
MODE
|
|
|
|
|
|
FOR NEW PHONE: Press FCN, 0 + Security code entered twice (Factory
|
|
preset is 000000), RCL
|
|
|
|
The message 01 will appear in the display to confirm programming mode.
|
|
|
|
Press * 01 Press *
|
|
|
|
1) _ _ _ _ _ Press * 02 Press *
|
|
|
|
2) XXX Press * 03 Press *
|
|
|
|
3) XXX XXXX Press * 04 Press *
|
|
|
|
4) 14 Press * 05 Press *
|
|
|
|
5) 07 Press * 06 Press *
|
|
|
|
6) 10 Press * 07 Press *
|
|
|
|
7) 123456 Press * 08 Press *
|
|
|
|
8) 123 Press * 09 Press *
|
|
|
|
9) 0334 Press * 10 Press *
|
|
|
|
10) 010101 Press * 11 Press *
|
|
|
|
11) 101 Press * 12 Press *
|
|
|
|
Review entries by pressing "*" repeatedly.
|
|
|
|
Press SEND to program phone.
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
NEC P300
|
|
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
THESE INSTRUCTIONS FOR SERIAL NUMBERS AFTER 135-839601
|
|
|
|
Insert NAM Programming Adapter (NECAM #41-2019) into plug connector on P300
|
|
phone bottom.
|
|
|
|
PWR On
|
|
|
|
RCL # 0 1 to enter test mode. Phone will display shaded blocks.
|
|
|
|
RCL # 7 6 to select NAM. Phone will show 76-
|
|
Press 0 # to program NAM 1. (NAM 1=0,NAM 2=1,NAM 3=2,NAM 4=3)
|
|
|
|
RCL # 7 1 to enter programming mode.
|
|
|
|
XXXXXXXXXX PRESS # MIN
|
|
|
|
1234 PRESS # LOCK CODE
|
|
|
|
_ _ _ _ _ PRESS # SID
|
|
|
|
10 PRESS # GROUP I.D.
|
|
|
|
0334 PRESS # INITIAL PAGING CH
|
|
|
|
0 PRESS # SYSTEM SELECT (1=A)
|
|
|
|
07 PRESS # ACCOLC
|
|
|
|
1 PRESS # MIN MARK 1
|
|
|
|
1 PRESS # LOCAL USE
|
|
|
|
911 PRESS # EMERGENCY NO.
|
|
|
|
Press Clr (and hold) to exit programming and return to TEST MODE.
|
|
|
|
Press RCL # 0 2 to burn and exit to standby.
|
|
|
|
|
|
|
|
THESE INSTRUCTIONS FOR SERIAL NUMBERS PRIOR TO 135-839601
|
|
|
|
Insert NAM Programming Cable (41-2019)
|
|
PWR on
|
|
RCL # 7 6 to enter TEST MODE
|
|
Press 0 # to select NAM.
|
|
RCL # 7 1
|
|
You are now in Programming Mode.
|
|
Enter NAM info as above.
|
|
Press and hold CLR to exit.
|
|
Pwr down.
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
NEC P9100
|
|
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
|
|
UNLOCK CODES WILL BE CHANGED ONLY IN PROGRAMMING MODE
|
|
FOLLOW THE INSTRUCTIONS THAT FOLLOW
|
|
|
|
|
|
|
|
Make sure NAM battery is fully charged before attempting programming
|
|
Switch power on
|
|
Press RCL #01 display will then show shaded blocks
|
|
|
|
For a USED phone - to clear nam and accumulated call timer
|
|
Press RCL #39
|
|
|
|
To program NAM1
|
|
Press RCL #760#
|
|
To enter programming mode Press RCL #71
|
|
|
|
XXXXXXXXXX Press # MIN
|
|
|
|
1234 Press # Lock Code
|
|
|
|
_ _ _ _ _ Press # SYS. I.D.
|
|
|
|
10 Press # G.I. Mark
|
|
|
|
0334 Press # First Paging Channel
|
|
|
|
0 Press # System Select
|
|
|
|
07 Press # ACCOLC
|
|
|
|
0 Press # MIN Mark
|
|
|
|
1 Press # Local Use
|
|
|
|
|
|
TO EXIT PROGRAM MODE AT THIS TIME PRESS CLR AND HOLD
|
|
DISPLAY WILL SHOW TEST MODE
|
|
|
|
TO EXIT TEXT MODE PRESS RCL#02
|
|
|
|
IF THE MEMORY IS CLEARED VIA RCL #39 DURING THE PROGRAMMING THEN THE PHONE
|
|
WILL AUTOMATICALLY ENTER FULL-LOCK AFTER EXITING THE TEST MODE
|
|
TO UNLOCK: FCN #XXXX(4 DIGIT LOCK CODE FOR LAST NAM PROGRAMMED).
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
NOKIA P-30
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
|
|
PRESS SEL 7 UNLCODE APPEARS ON THE DISPLAY
|
|
ENTER 5 DIGIT SECURITY CODE AND THE CURRENT UNLOCK CODE APPEARS IN
|
|
THE DISPLAY PRESS CLR AND ENTER THE NEW FOUR DIGIT UNLOCK CODE
|
|
PRESS SEL TO STORE THE NEW CODE - NOTE: IF YOU DON'T PRESS SEL WITHIN
|
|
FIVE SECONDS THE DISPLAY WILL CLEAR AND CANCEL THE FUNCTION
|
|
|
|
|
|
PWR up unit
|
|
Enter *17*2001*12345*
|
|
HO-Id must appear on display
|
|
Press SEL to view current value
|
|
Display will be one step behind TO STORE instructions
|
|
|
|
|
|
_ _ _ _ _ Press SEL ACCESS (SID)
|
|
|
|
1 Press SEL LOCAL
|
|
|
|
1 Press SEL PhonE n
|
|
|
|
XXXXXXXXXX Press SEL CLASS
|
|
|
|
10 Press SEL PAGE ch
|
|
|
|
334 Press SEL O-LOAd
|
|
|
|
07 Press SEL GrouP
|
|
|
|
10 Press SEL SEC
|
|
|
|
12345 Press SEL AUTO EXIT PROGRAM MODE
|
|
|
|
TO EXIT PROGRAMMING MODE AT ANY TIME PRESS "END"
|
|
|
|
WHEN THE SEL KEY IS PRESSED FOLLOWING THE LAST PARAMETER VALUE, THE PHONE
|
|
WILL AUTOMATICALLY EXIT THE NAM PROGRAMMING MODE AND RETURN TO NORMAL
|
|
OPERATION
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
NOVATEL PTR800
|
|
|
|
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
|
|
UNLOCK CODES WILL BE CHANGED ONLY IN PROGRAMMING MODE
|
|
FOLLOW THE INSTRUCTIONS THAT FOLLOW
|
|
|
|
|
|
PWR up unit
|
|
Press FCN
|
|
Press FCN again
|
|
Enter *626776*
|
|
Display will show CMT REV and a date code - Press Volume Up
|
|
Display will show NAM SELECT1 Press Volume Up
|
|
|
|
_ _ _ _ _ PRESS # PRESS VOLUME UP SIDH
|
|
PRESS VOLUME UP SCM
|
|
XXXXXXXXXX PRESS # PRESS VOLUME UP MIN
|
|
0333 PRESS # PRESS VOLUME UP IDCCA
|
|
0334 PRESS # PRESS VOLUME UP IDCCB
|
|
0334 PRESS # PRESS VOLUME UP IPCH
|
|
07 PRESS # PRESS VOLUME UP ACCOLC
|
|
10 PRESS # PRESS VOLUME UP GIM
|
|
123 PRESS # PRESS VOLUME UP LOCK A
|
|
456 PRESS # PRESS VOLUME UP LOCK B
|
|
1 PRESS # PRESS VOLUME UP OPTION LC
|
|
1 PRESS # PRESS VOLUME UP OPTION EX
|
|
0 PRESS # PRESS VOLUME UP OPTION PS
|
|
0 PRESS # PRESS VOLUME UP OPTION NSC
|
|
1 PRESS # PRESS VOLUME UP OPTION EE
|
|
1 PRESS # PRESS VOLUME UP OPTION REP
|
|
0 PRESS # PRESS VOLUME UP OPTION HA
|
|
0 PRESS # PRESS VOLUME UP OPTION HF
|
|
0 PRESS # PRESS VOLUME UP OPTION F1
|
|
0 PRESS # PRESS VOLUME UP OPTION F2
|
|
0 PRESS # PRESS VOLUME UP OPTION F3
|
|
0 PRESS # PRESS VOLUME UP OPTION F4
|
|
|
|
TO EXIT PROGRAMMING MODE AT ANY TIME PRESS FCN END
|
|
|
|
FCN FCN *6462257* WILL CLEAR THE NAM IF IT HAS BEEN PROGRAMMED MORE THAN
|
|
3 TIMES OR IF THE NEED EXISTS TO CLEAR THE MEMORY
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
NOVATEL PTR825
|
|
|
|
ACTION TO STORE DISPLAY
|
|
PWR up unit
|
|
Press FCN
|
|
Press FCN again
|
|
Enter *697201*
|
|
Display will show CMT REV 972 105 Press Volume Up
|
|
|
|
1 PRESS # VOL UP NAM SELECT 1
|
|
_ _ _ _ _ PRESS # VOL UP SIDH
|
|
10 PRESS VOL UP SCM
|
|
XXXXXXXXXX PRESS # VOL UP MIN
|
|
0333 PRESS VOL UP IDCCA
|
|
0334 PRESS VOL UP IDCCB
|
|
0334 PRESS # VOL UP IPCH
|
|
07 PRESS # VOL UP ACCOLC
|
|
10 PRESS # VOL UP GIM
|
|
123 PRESS # VOL UP LOCK A
|
|
123 PRESS # VOL UP LOCK B
|
|
1 PRESS # VOL UP LC
|
|
1 PRESS # VOL UP OPTION EX
|
|
0 PRESS # VOL UP PS - PREF SYSTEM
|
|
0 PRESS VOL UP OPTION NSC
|
|
1 PRESS # VOL UP OPTION EE-END TO END
|
|
1 PRESS # VOL UP OPTION REP
|
|
0 PRESS # VOL UP HORN ALERT
|
|
0 PRESS # VOL UP HANDS FREE
|
|
0 PRESS # VOL UP OPTION F1
|
|
0 PRESS # VOL UP OPTION F2
|
|
0 PRESS # VOL UP OPTION F3
|
|
1 PRESS # VOL UP OPTION F4 AIR RND UP
|
|
0 PRESS # VOL UP OPTION F5 FUTURE USE
|
|
0 PRESS # VOL UP OPTION F6 FUTURE USE
|
|
0 PRESS # VOL UP OPTION F7 FUTURE USE
|
|
|
|
|
|
|
|
Programming will now wrap to beginning SIDH display.
|
|
Press VOL UP to review entries
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
OKI HANDHELD MODEL # 750
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
|
|
THIS FUNCTION IS PROVIDED FOR IN THE PROGRAMMING SEQUENCE
|
|
|
|
|
|
|
|
|
|
Pwr up unit
|
|
Press (*) and (#) simultaneously
|
|
Enter 10 digit Sec Code as follows: *12345678#
|
|
What follows can be done only once!
|
|
|
|
The display "Enter NEW PW-Sto"
|
|
Enter 0123456789 then press STORE
|
|
|
|
Pwr unit down.
|
|
|
|
Pwr up unit
|
|
Press MENU and RCL simultaneously
|
|
Enter 0123456789 Software Version and
|
|
ESN Number in HEX
|
|
|
|
Clears in 2 secs.
|
|
|
|
Spd Dial Mem Clear
|
|
|
|
Press 0 Press STO Def Data Reset
|
|
|
|
Press 0 Press STO
|
|
|
|
NAM 1 Mode
|
|
|
|
Own #111 111-1111
|
|
|
|
XXX XXX XXXX Press STO Vol Up Security
|
|
|
|
123456 Press STO Vol Up OPTION
|
|
|
|
1100 Press STO Vol Up SCM
|
|
|
|
1010 Press STO Vol Up GIM
|
|
|
|
10 Press STO Vol Up Unlock #
|
|
|
|
1234 Press STO Vol Up ACCOLC #
|
|
|
|
07 Press STO Vol Up IPCH NO.
|
|
|
|
0334 Press STO Vol Up
|
|
|
|
_ _ _ _ _ Press STO Vol Up System ID:
|
|
|
|
At this time you may exit the programming mode by pressing CLR to bypass
|
|
the other NAM modules.
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
OKI HANDHELD MODEL # 900
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
|
|
THIS FUNCTION IS PROVIDED FOR IN THE PROGRAMMING SEQUENCE
|
|
|
|
|
|
Pwr up unit
|
|
Press RCL and MENU simultaneously
|
|
Enter 10 digit Sec Code as follows: *12345678#
|
|
What follows can be done only once!
|
|
|
|
The display "Enter NEW PW-Sto"
|
|
Enter 0123456789 then press STORE.
|
|
The display "Re-Enter New PW-Sto"
|
|
Enter 0123456789 then press STORE to enter Programming Mode.
|
|
IF You don't wish to keep the new password then Pwr unit down.
|
|
|
|
|
|
Software Version and
|
|
ESN Number in HEX
|
|
|
|
Clears in 2 secs.
|
|
|
|
Spd Dial Mem Clear
|
|
|
|
Press * Press STO SPD DIAL MEM CLEAR
|
|
|
|
Press * Press STO DEFAULT DATA CLEAR
|
|
|
|
NAM 1 Mode
|
|
|
|
Own #111 111-1111
|
|
|
|
XXX XXX XXXX Press STO Vol Up MIN
|
|
|
|
123456 Press STO Vol Up SECURITY
|
|
|
|
_ _ _ _ _ Press STO Vol Up SYSTEM ID:
|
|
|
|
0334 Press STO Vol Up IPCH
|
|
|
|
07 Press STO Vol Up ACCOLC #
|
|
|
|
15 Press STO Vol Up GROUP I.D.
|
|
|
|
1234 Press STO Vol Up UNLOCK CODE
|
|
|
|
1010 Press STO Vol Up STATION CLASS
|
|
|
|
1110 Press STO Vol Up OPTION
|
|
|
|
|
|
|
|
At this time you may exit the programming mode by pressing CLR to bypass
|
|
the other NAM modules.
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
PANASONIC EB3500
|
|
|
|
|
|
|
|
Charged Battery and Nam Adaptor are needed.
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
|
|
THIS FUNCTION IS PROVIDED FOR IN THE PROGRAMMING SEQUENCE
|
|
|
|
|
|
|
|
|
|
*0000# to enter program mode
|
|
|
|
|
|
*1 Press SND NAM 1 MODE
|
|
|
|
_ _ _ _ _ Press STO 01 SIDH
|
|
|
|
XXXXXXXXXX Press STO 02 OWNDL
|
|
|
|
0 Press STO 03 PRESYS
|
|
|
|
334 Press STO 04 IPCH
|
|
|
|
07 Press STO 05 ACCOLC
|
|
|
|
10 Press STO 06 GIM
|
|
|
|
00 Press STO 07 DLMT
|
|
|
|
10 Press STO 08 SCM
|
|
|
|
911 Press STO 09 SPDL
|
|
|
|
1234 Press STO 10 LOCK
|
|
|
|
1 1 0 1 1 0 0 0 Press STO 11 FCN 1
|
|
|
|
0 0 0 1 0 1 0 0 Press STO 12 FCN 2
|
|
|
|
1 1 1 1 0 1 1 1 Press STO 13 FCN 3
|
|
|
|
STO **
|
|
END to program phone
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
COLT TRANSPORTABLE
|
|
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
|
|
UNLOCK CODES WILL BE CHANGED ONLY IN PROGRAMMING MODE
|
|
FOLLOW THE INSTRUCTIONS THAT FOLLOW
|
|
|
|
Phone must be locked, to accomplish: press FUNC 5
|
|
Enter: FUNC #626# FUNC
|
|
The software revision date will be shown.
|
|
Press SEND
|
|
This will advance phone through memory locations.
|
|
E.S.N. will be displayed, press SEND again.
|
|
|
|
XXX Press SEND AREA CODE
|
|
|
|
XXX XXXX Press SEND PHONE NUMBER
|
|
|
|
_ _ _ _ _ Press SEND SYSTEM ID
|
|
|
|
07 Press SEND ACCOLC
|
|
|
|
10 Press SEND GIM
|
|
|
|
1 Press SEND LOCAL USE MARK
|
|
|
|
1 Press SEND MIN MARK (MOBILE ID)
|
|
|
|
123 Press SEND LOCK CODE
|
|
|
|
0 Press SEND AUTOMATIC LOCK
|
|
|
|
123 Press SEND CALL RESTRICTION
|
|
|
|
12 Press SEND CALL COUNTER RESET
|
|
|
|
1 Press SEND ENABLE HANDSFREE
|
|
|
|
0 Press SEND DISABLE HORN ALERT
|
|
|
|
0 Press SEND HA TURN OFF TIME
|
|
|
|
12 Press SEND TOTAL AIRTIME RESET
|
|
|
|
TO REVIEW PROGRAMMING AT THIS TIME PRESS SEND.
|
|
|
|
TO EXIT PROGRAMMING AND STORE DATA AT ANY TIME PRESS
|
|
END FUNC END - WAKE UP WILL SOUND, PHONE WILL BE LOCKED
|
|
ENTER UNLOCK CODE- 123
|
|
|
|
SYSTEM PREFERENCE MUST BE KEYPAD SELECTED! PRESS FUNC 7 FOR "A" NON W/L
|
|
|
|
OR PRESS FUNC 8 FOR "B" W/L SYS.
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
DIAMONDTEL MESA 55 TRANSPORTABLE
|
|
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
PWR up unit
|
|
Press "CL" and hold within 10 seconds of pwr up
|
|
Enter "1951426"
|
|
Current Mobile I.D. will display
|
|
|
|
XXXXXXXXXX Press SEND MIN
|
|
|
|
123 Press SEND 1 SECURITY
|
|
|
|
_ _ _ _ _ Press SEND 2 SID
|
|
|
|
1 Press SEND 3 LU
|
|
|
|
1 Press SEND 4 MIN MARK
|
|
|
|
334 Press SEND 5 IPCH
|
|
|
|
07 Press SEND 6 ACCOLC
|
|
|
|
0 Press SEND 7 PREF SYS
|
|
|
|
10 Press SEND 8 GIM
|
|
|
|
1 Press SEND 9 EE
|
|
|
|
1 Press SEND 10 ENBL HANDSFREE
|
|
|
|
0 Press SEND 11 RI
|
|
|
|
04 Press SEND 12 AUX 1
|
|
|
|
07 Press SEND 13 AUX 2
|
|
|
|
Phone automatically returns to show the 10 digits MIN number at this time
|
|
and to indicate that the NAM has been programmed. The END key should be
|
|
pressed to burn the NAM.
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
DIAMONDTEL MESA95 TRANSPORTABLE
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
PWR up unit
|
|
Press and hold Clr within 10 Seconds of pwr up
|
|
Enter "1951426"
|
|
Release Clr
|
|
|
|
|
|
0 Press SEND duaAL no
|
|
|
|
XXXXXXXXXX Press SEND no1
|
|
|
|
_ _ _ _ _ Press SEND SId1
|
|
|
|
1 Press SEND LU1
|
|
|
|
1 Press SEND E1
|
|
|
|
334 Press SEND IPCH1
|
|
|
|
07 Press SEND ACCOLC1
|
|
|
|
0 Press SEND PS1
|
|
|
|
10 Press SEND GI1
|
|
|
|
5 Press SEND t InC1
|
|
|
|
1234 Press SEND SECUrIty
|
|
|
|
1 Press SEND EE
|
|
|
|
0 Press SEND dt
|
|
|
|
0 Press SEND HF
|
|
|
|
0 Press SEND InHIbIt
|
|
|
|
1 Press SEND Ctone
|
|
|
|
0 Press SEND dIS CU
|
|
|
|
0 Press SEND dIS IGn
|
|
SEnSE
|
|
|
|
0 Press SEND DUAL HS
|
|
|
|
|
|
TO EXIT PROGRAMMING MODE PRESS "END" AT ANY TIME
|
|
|
|
TO RESET NAM FROM THE LIMIT OF 3 PROGRAM ATTEMPTS
|
|
FOLLOW THE BLOCK OF INSTRUCTIONS AT TOP USING "8291112" W/CLR
|
|
|
|
TO RESET NAM OF MESA 90 HANDHELD USE THE CODE "6972814"
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
FUJITSU MOBILE PHONE
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
PWR up unit
|
|
Unit must be locked to program.
|
|
To lock press F+LOCK
|
|
PWR down unit.
|
|
PWR up unit.
|
|
Within 10 seconds press #626#7764726 (#NAM#PROGRAM)
|
|
A continuous tone will be heard for 7 seconds.
|
|
PRESS AND HOLD THE * KEY WHILE THE TONE SOUNDS,
|
|
DO NOT LET GO!
|
|
The tone will change to an intermittent tone, then it will stop.
|
|
Release the * key.
|
|
|
|
CONGRATULATIONS!!! YOU ARE NOW IN PROGRAMMING MODE!
|
|
|
|
_ _ _ _ _ PRESS STOR 1 SIDH
|
|
|
|
1 PRESS STOR 2 LOCAL
|
|
|
|
1 PRESS STOR 3 MIN MARK
|
|
|
|
XXXXXXXXXX PRESS STOR 4 MIN
|
|
|
|
10 PRESS STOR 5 STATION
|
|
|
|
0334 PRESS STOR 6 IPCH
|
|
|
|
07 PRESS STOR 7 ACCOLC
|
|
|
|
0 PRESS STOR 8 PS
|
|
|
|
10 PRESS STOR 9 GIM
|
|
|
|
1234 PRESS STOR 10 LOCK
|
|
|
|
1 PRESS STOR 11 CALL TIME
|
|
|
|
2 PRESS STOR 12 AUTO LOCK
|
|
|
|
1 PRESS STOR 13 CALL REST
|
|
|
|
PRESS STOR TO REVIEW ENTRIES.
|
|
WHEN AT MODE #1 PRESS SEND TO BURN NAM AND RETURN TO NORMAL OPERATION.
|
|
|
|
IF PROGRAMMING WAS DONE INCORRECTLY A SHORT HIGH TONE WILL BE HEARD, YOU
|
|
MUST THEN REPEAT DATA ENTRY. YOU MUST PRESS STOR AFTER EACH ENTRY FOR THE
|
|
CHECKSUM FUNCTION TO BE FULFILLED.
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
GENERAL ELECTRIC CARFONE XR3000
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
|
|
THE UNLOCK CODE IS PROGRAMMED IN STEP 2 OF THE PROGRAMMING
|
|
MODE
|
|
|
|
|
|
|
|
PWR up unit
|
|
Press "CL" and hold within 10 seconds of pwr up
|
|
Enter "923885"
|
|
Serial # will display
|
|
Press Send key to advance to first entry
|
|
|
|
XXXXXXXXXX Press SEND MIN
|
|
|
|
123 Press SEND UNLOCK
|
|
|
|
_ _ _ _ _ Press SEND SID
|
|
|
|
1 Press SEND LU
|
|
|
|
1 Press SEND MIN MARK
|
|
|
|
334 Press SEND IPCH
|
|
|
|
07 Press SEND ACCOLC
|
|
|
|
0 Press SEND PS
|
|
|
|
10 Press SEND GIM
|
|
|
|
0 Press SEND AUX
|
|
|
|
1 Press SEND HANDS
|
|
|
|
|
|
PRESS SEND TO REVIEW ENTRIES. NOTE: AREA CODE (402) WILL DISPLAY FOR MIN
|
|
THEN AUTO SWITCH TO REST OF NUMBER ON DISPLAY - BE PATIENT
|
|
|
|
PRESS "E" KEY TO COMPLETE PROGRAMMING OF THE XR 3000 AT THIS TIME
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
GOLDSTAR SERIES 5000 MOBILE
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
PWR up Unit
|
|
Press FCN 4 to see the selected NAM. Press * to advance. Select NAM1.
|
|
Press FCN, 9, 9, * "Enter Code" will be displayed.
|
|
Enter 1234567890
|
|
|
|
XXXXXXXXXX PRESS MEM Enter MIN
|
|
|
|
_ _ _ _ _ PRESS MEM Enter System ID
|
|
|
|
0334 PRESS MEM Enter IPCH
|
|
|
|
07 (ACCOLC) PRESS MEM Enter OVLD Class
|
|
|
|
1234 PRESS MEM LOCK CODE
|
|
|
|
123456 PRESS MEM SECURITY CODE
|
|
|
|
1234 PRESS MEM ALARM DISARM CODE
|
|
|
|
0 PRESS MEM PREFFERED SYSTEM
|
|
|
|
0 PRESS MEM STATION CLASS MARK
|
|
|
|
1 PRESS MEM HANDS FREE MARK (ON)
|
|
|
|
1 PRESS MEM LOCAL USE MARK (ON)
|
|
|
|
1 PRESS MEM MIN MARK (ON)
|
|
|
|
0 PRESS MEM HORN ALERT (OFF)
|
|
|
|
0 PRESS MEM OPT. SPEAKER (OFF)
|
|
|
|
TO SAVE TO NAM NOW PRESS MEM
|
|
|
|
TO REVIEW ENTRIES USE THE VOLUME UP OR DOWN KEYS
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
MITSUBISHI 555,560,600
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
|
|
TO PROGRAM THIS FUNCTION YOU MUST BE OUT OF THE PROGRAMMING MODE
|
|
ENTER FCN 6 AND THEN ENTER THE NEW 3 DIGIT UNLOCK CODE
|
|
PRESS CLR.
|
|
|
|
To program from keypad remove and discard Nam Pad
|
|
PWR up unit
|
|
Press and Hold STO key within 10 seconds of pwr up
|
|
Enter "5474432"
|
|
Release STO key
|
|
|
|
XXXXXXXXXX Press SEND MIN
|
|
|
|
123 Press SEND SECURITY CODE
|
|
|
|
_ _ _ _ _ Press SEND SID
|
|
|
|
1 Press SEND LU
|
|
|
|
1 Press SEND MIN MARK
|
|
|
|
334 Press SEND IPCH1
|
|
|
|
07 Press SEND ACCOLC1
|
|
|
|
0 Press SEND PS1
|
|
|
|
10 Press SEND GIM
|
|
|
|
1 Press SEND EE
|
|
|
|
1 Press SEND HANDS FREE
|
|
|
|
0 Press SEND ROAM INHIBIT
|
|
|
|
0 Press SEND A/B SELECT
|
|
|
|
00 Press SEND f3-f0 DUAL HEAD
|
|
|
|
00 Press SEND f7-f4 LD INH
|
|
|
|
TO EXIT PROGRAMMING MODE PRESS "END" AT ANY TIME
|
|
|
|
Installing the LOCK CODE
|
|
|
|
To program the customer's lock code, the phone must be out ot the
|
|
programming mode.
|
|
To program, enter FCN, 6,3-digit security code, the a 3-digit lock code.
|
|
Press CLR.
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
NEC M3700 SERIES MOBILE
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
|
|
UNLOCK CODES WILL BE CHANGED ONLY IN PROGRAMMING MODE
|
|
FOLLOW THE INSTRUCTIONS THAT FOLLOW
|
|
|
|
A NAM PROGRAMMER ADAPTOR (NECAM #41-2012) IS
|
|
REQUIRED
|
|
|
|
PWR UP
|
|
|
|
TO ENTER TEST MODE:
|
|
|
|
RCL, #,0,1. WILL CYCLE TO SHADED
|
|
|
|
TO CLEAR MEMORY:
|
|
|
|
RCL # 3 9
|
|
select nam
|
|
RCL # 7 6 0 # nam 1
|
|
RCL # 7 6 1 # nam 2
|
|
|
|
TO ENTER PROGRAMMING MODE:
|
|
|
|
RCL #71
|
|
|
|
|
|
XXX XXX XXXX PRESS # Telephone No. (MIN)
|
|
|
|
1234 PRESS # Lock Code
|
|
|
|
_ _ _ _ _ PRESS # Home Area (SYS I.D.)
|
|
|
|
10 PRESS # G-NO (Group I.D.)
|
|
|
|
0334 PRESS # First Paging Channel
|
|
|
|
0 for wireline PRESS # System Select
|
|
|
|
07 PRESS # ACCOLC
|
|
|
|
1 PRESS # ACCESS
|
|
|
|
1 PRESS # Local Use
|
|
|
|
|
|
To exit PROGRAMMING MODE PRESS CLR and hold TEST MODE will show
|
|
|
|
to exit TEST MODE RCL #02
|
|
|
|
IF MEM WAS CLEARED VIA RCL #39, PHONE WILL AUTOMATICALLY ENTER FULL-LOCK
|
|
AFTER EXITING THE TEST MODE.
|
|
TO UNLOCK PRESS FCN # 1234.
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
NOKIA LX-11
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
|
|
PRESS SEL,5 THEN ENTER 5 DIGIT SECURITY CODE
|
|
PRESS SEL TO RECEIVE DISPLAY OF CURRENT UNLOCK CODE
|
|
PRESS 5 NOW TO CLEAR ALL CALL TIMERS
|
|
ENTER THE NEW UNLOCK CODE
|
|
PRESS SEL TO ACCEPT
|
|
|
|
PWR up unit
|
|
Enter *3001#12345 Then - SEL 9 END
|
|
IdEnt IF InFO should appear on display
|
|
|
|
Pressing END will move you through the parameters
|
|
Pressing SND will toggle between choices available
|
|
|
|
_ _ _ _ _ Press END HO-Id (SID)
|
|
|
|
1 Press END ACCESS
|
|
|
|
1 Press END LOCL OPt
|
|
|
|
XXXXXXXXXX Press END Phonxx
|
|
|
|
08 Press END St CLASS
|
|
|
|
334 Press END PAging Ch
|
|
|
|
07 Press END O-LOAd CLASS
|
|
|
|
B Press END PrEF SyS
|
|
|
|
10 Press END grOUP Id
|
|
|
|
12345 Press END SECUrIty
|
|
|
|
-------- (Can't be changed) Press END 1 dAtE
|
|
|
|
00/00/90 (INSTALLATION DATE) Press END 2 dAtE
|
|
|
|
|
|
TO EXIT PROGRAMMING MODE AT ANY TIME PRESS "END" TO STORE LAST PARAMETER
|
|
THEN POWER DOWN
|
|
WHEN THE "END" KEY IS PRESSED FOLLOWING THE LAST PARAMETER, THE TEXT
|
|
Prog donE WILL APPEAR ON DISPLAY
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
NOKIA M-10
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
|
|
THIS FUNCTION IS PROVIDED BY THE SECURITY CODE PROGRAMMED AT THE
|
|
TIME OF PROGRAMMING
|
|
|
|
|
|
|
|
PWR up unit
|
|
Enter *17*3001*1234*
|
|
HO-Id must appear on display
|
|
Press SEL to view current value
|
|
Display will be one step behind TO STORE instructions
|
|
|
|
|
|
_ _ _ _ _ Press SEL ACCESS (SID)
|
|
|
|
1 Press SEL LOCAL
|
|
|
|
1 Press SEL PhonE n
|
|
|
|
XXXXXXXXXX Press SEL CLASS
|
|
|
|
08 Press SEL PAGE ch
|
|
|
|
334 Press SEL O-LOAd
|
|
|
|
07 Press SEL GrouP
|
|
|
|
10 Press SEL SEC
|
|
|
|
1234 Press SEL AUTO EXIT PROGRAM MODE
|
|
|
|
TO EXIT PROGRAMMING MODE AT ANY TIME PRESS "END"
|
|
|
|
WHEN THE SEL KEY IS PRESSED FOLLOWING THE LAST PARAMETER VALUE, THE PHONE
|
|
WILL AUTOMATICALLY EXIT THE NAM PROGRAMMING MODE AND RETURN TO NORMAL
|
|
OPERATION
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
NOVATEL 8305 TRANSPORTABLE
|
|
|
|
CA08 SOFTWARE VERSION
|
|
|
|
USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
|
|
IF EQUIPMENT IS PROVIDED WITH A MENU KEY THEN ENTER THE MENU PORTION OF
|
|
THE PHONE AND DISPLAY AND IF NECESSARY REPROGRAM THE UNLOCK CODE FROM
|
|
THERE.
|
|
IF PHONE DOES NOT HAVE A MENU KEY THEN THERE CAN BE NO PROGRAMMING OF THE
|
|
UNLOCK CODE... THE SECURITY CODE WILL BE ALL THAT IS PROVIDED
|
|
|
|
Lock Phone by pressing FCN 1
|
|
Enter Programming Mode by pressing #259
|
|
|
|
Screen will display the software revision number
|
|
Press Volume Up
|
|
|
|
Screen will display Phone's E.S.N.
|
|
Press Volume Up
|
|
|
|
Screen will display INIT REP USE SND
|
|
Press SEND to erase any numbers stored in the phones memory
|
|
Press Volume Up
|
|
|
|
_ _ _ _ _ Send Vol. Up SIDH system I.D.
|
|
|
|
XXX XXX XXXX Send Vol. Up MIN mobile I.D.
|
|
|
|
Must be changed when done Send Vol. Up LOCK CODE 1
|
|
programming - BY CUSTOMER
|
|
Must be changed when done Send Vol. Up LOCK CODE 2
|
|
programming - BY CUSTOMER
|
|
SET Vol. Up Option EX extnd adrss
|
|
334 press send to change Vol. Up IPCH initial pge
|
|
07 Send Vol. Up ACCOLC overload
|
|
10 Send Vol. Up GIM group i.d.
|
|
333 Vol. Up IDCCA initl a
|
|
334 Vol. Up IDCCB initl b
|
|
1 Vol. Up REG TBL SIZE
|
|
Volume up through the four invalid System I.D. addresses
|
|
SET Vol. Up OPTION LU local use
|
|
B press send to change Vol. Up OPTION PS (prefered sys)
|
|
CLR Vol. Up OPTION IRI rm inhbt
|
|
CLR Vol. Up OPTION SSD
|
|
SET Vol. Up OPTION QRC qck rcall
|
|
SET Vol. Up OPTION QST qck store
|
|
SET Vol. Up OPTION WUT wake tone
|
|
SET Vol. Up OPTION EE use dtmf
|
|
SET Vol. Up OPTION FD use dtmf
|
|
SET Vol. Up OPTION MFD ext dtmf
|
|
SET Vol. Up OPTION 32D dgt dial
|
|
CLR Vol. Up OPTION MLH timer
|
|
CLR Vol. Up OPTION LHM timer
|
|
CLR Vol. Up OPTION CRU timer dsp
|
|
CLR Vol. Up OPTION NLM timer
|
|
SET for on CLR for off Vol. Up OPTION HA hrn alert
|
|
CLR Vol. Up OPTION ONL diagnostc
|
|
END to exit or VOLUME UP to review entries.
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
OKI CDL400
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
To Enter Programming mode:
|
|
|
|
Press IN SEQUENCE:
|
|
END RCL FUNC CLR SND
|
|
|
|
Screen shows Entr id
|
|
|
|
Enter 08693427
|
|
|
|
XXX XXX XXXX PRESS # PRESS * PHon
|
|
|
|
_ _ _ _ _ PRESS # PRESS * S id no
|
|
|
|
0334 PRESS # PRESS * iPCH
|
|
|
|
07 PRESS # PRESS * ACC oLC
|
|
|
|
123 PRESS # PRESS * LoC Cod
|
|
|
|
10 PRESS # PRESS * G id
|
|
|
|
0000 PRESS # PRESS * Stn CLS
|
|
|
|
0111 PRESS # PRESS * HORN ALERT, HANDS
|
|
FREE, LOCAL USE,
|
|
MIN. MARK.
|
|
|
|
PRESS END AT THIS TIME TO EXIT PROGRAMMING MODE.
|
|
|
|
__________________________________________________________________________
|
|
|
|
TO REPROGRAM TELEPHON NUMBER AND SYSTEM I.D. # -
|
|
|
|
PRESS IN SEQUENCE THE FOLLOWING KEYSTROKES:
|
|
|
|
FUNC 90 * 123 (SECURITY CODE)
|
|
|
|
PHon WILL DISPLAY
|
|
|
|
ENTER NEW PHONE NUMBER
|
|
|
|
XXX XXX XXXX PRESS # PRESS * PHon
|
|
|
|
_ _ _ _ _ PRESS # PRESS * S id no
|
|
|
|
PRESS END AT THIS TIME TO EXIT PROGRAMMING MODE.
|
|
|
|
___________________________________________________________________________
|
|
|
|
To Re-Initialize Nam Memory for Handset Programmable Models -
|
|
Func 99*
|
|
Enter Last 8 digits of S.N.
|
|
Press *
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
PANASONIC EB362
|
|
|
|
|
|
|
|
Charged Battery and Nam Adaptor(Grey Cord w/25pin Connector)are needed.
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
|
|
THIS FUNCTION IS PROVIDED FOR IN THE PROGRAMMING SEQUENCE
|
|
|
|
|
|
|
|
|
|
*0000# to enter program mode
|
|
|
|
*1 Press SND
|
|
|
|
50 Press SND NAM 1 MODE
|
|
|
|
_ _ _ _ _ Press STO 01 SIDH
|
|
|
|
XXXXXXXXXX Press STO 02 OWNDL
|
|
|
|
1 2 3 Press STO 03 LOCK
|
|
|
|
0 0 0 0 0 0 0 0 0 0 0 0 (12) Press STO 04 SPDL
|
|
|
|
00 Press STO 05 SCM
|
|
|
|
334 Press STO 06 IPCH
|
|
|
|
07 Press STO 07 ACCOLC
|
|
|
|
10 Press STO 08 GIM
|
|
|
|
1 1 0 1 1 1 0 0 Press STO 09 FEATURE A
|
|
|
|
0 0 0 0 0 1 0 0 Press STO 10 FEATURE B
|
|
|
|
1 0 0 0 0 0 1 1 Press STO 11 FEATURE C
|
|
|
|
00 Press STO 12 DLMT
|
|
|
|
STO **
|
|
Turn power off
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
PANASONIC EB-500 OR TP-500
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
USED EQUIPMENT: TO DISPLAY CURRENT UNLOCK CODE -
|
|
THIS FUNCTION IS PROVIDED FOR IN THE PROGRAMMING SEQUENCE
|
|
|
|
Attach Nam Programmer Cable (Our Stock # 823)
|
|
|
|
Pwr up unit
|
|
|
|
Enter *0000# 0
|
|
|
|
*1 SND
|
|
You are now in the NAM 1 Program mode.
|
|
|
|
_ _ _ _ _ Press STO 01 S.I.D.
|
|
|
|
XXXXXXXXXX Press STO 02 OWN #
|
|
|
|
0 Press STO 03 O for W/L system
|
|
|
|
334 Press STO 04 IPCH
|
|
|
|
07 Press STO 05 ACCOLC
|
|
|
|
10 Press STO 06 GIM
|
|
|
|
00 Press STO 07 Digit Dial Limit
|
|
|
|
08 Press STO 08 SCM (3watt i.d.)
|
|
|
|
911 Press STO 09 Rcl 00
|
|
|
|
1234 Press STO 10 Security Code
|
|
|
|
11000000 Press STO 11 FUNCTION BYTE 1
|
|
|
|
00010010 Press STO 12 FUNCTION BYTE 2
|
|
|
|
10010111 Press STO 13 FUNCTION BYTE 3
|
|
|
|
TO BURN NAM AT THIS TIME Press STO ** NAM is burned
|
|
|
|
Turn off unit
|
|
Detach programming cable
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
RADIO SHACK 17-1002 TRANSPORTABLE
|
|
|
|
THIS UNIT REQUIRES A SERVICE HANDSET TO BE PROGRAMMED!!!
|
|
|
|
A Mobira Service Handset (Modified) may be used. It is made from an ME53
|
|
or ME57 handset by opening and adding a jumper to the left of the one
|
|
factory installed just below the white 24 pin connector joining the top and
|
|
bottom PCB's. Also, pins 1 and 14 of the handset connector must be jumpered
|
|
at the radio end. To disassemble the handset, carefully pry off the
|
|
plastic earpad retaining housing to expose on hexdrive screw. Two other
|
|
screws are under the rubber plugs at either side of the microphone. The
|
|
handset then splits apart. This is a ticklish job and isn't recommended
|
|
except in an extreme case and not with the customer's handset. The
|
|
modification does not affect normal operation of the handset. It is not
|
|
known if a Radio Shack handset will work the same.
|
|
|
|
After the Service Handset has been applied -
|
|
|
|
To enter LOCAL MODE (which takes the phone off the air and allows service
|
|
commands to be obeyed) press 01#. The display should clear and noise is
|
|
heard from the earpiece.
|
|
|
|
To enter the NAM programming mode, enter 48#. The display shows 48 briefly
|
|
and clears.
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
|
|
0 _ _ _ _ _ PRESS * (5 Digit SID)
|
|
|
|
1 1 PRESS *
|
|
|
|
2 1 PRESS *
|
|
|
|
3 XXXXXXXXXX PRESS *
|
|
|
|
4 10 PRESS *
|
|
|
|
5 334 PRESS *
|
|
|
|
6 07 PRESS *
|
|
|
|
7 0 PRESS *
|
|
|
|
8 10 PRESS *
|
|
|
|
9 12345 PRESS *
|
|
|
|
Press * to exit NAM Programming Mode and return to Local Mode.
|
|
|
|
To enter the NAM reading Mode, press 49#. The display will show 49
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
RADIO SHACK 17-1003 TRANSPORTABLE
|
|
|
|
|
|
*17*1003* To enter program mode. If screen does not clear, enter 1234*
|
|
|
|
Screen
|
|
|
|
|
|
|
|
|
|
Programming Instructions for:
|
|
|
|
UNIDEN CP- 900 THRU 5000 SERIES MOBILES AND TRANSPORTABLES
|
|
|
|
|
|
THIS UNIT REQUIRES A PROGRAMMING HANDSET (MODEL CP-210 DIAGNOSTIC)
|
|
|
|
Make sure the unit is properly connected to a 13.8 volt supply (cig
|
|
lighter) and power on after utility handset is attached.
|
|
|
|
Upon connecting utility handset to phone, the display will show 1 on the
|
|
upper line and OP in the middle.
|
|
|
|
You are now in the TEST MODE!
|
|
|
|
Press SELECT, 2, SEND Top will show 2 0 and Current S.I.D.
|
|
|
|
You are now in the PROGRAM MODE
|
|
|
|
ACTION TO STORE DISPLAY
|
|
|
|
0 _ _ _ _ _ PRESS STORE SID
|
|
|
|
1 1 PRESS STORE LOCAL USE
|
|
|
|
2 1 PRESS STORE ACCES METH (MIN MARK)
|
|
|
|
3 XXXXXXXXXX PRESS STORE MIN
|
|
|
|
4 0334 PRESS STORE INITIAL PAGING CH
|
|
|
|
5 07 PRESS STORE ACCESS OVERLOAD
|
|
|
|
6 0 PRESS STORE PREF SYS (O-B,1-A)
|
|
|
|
7 10 PRESS STORE GROUP I.D. MARK
|
|
|
|
8 1234 PRESS STORE LOCK CODE (SEE re:)
|
|
|
|
9 1 PRESS STORE DTMF DURATION
|
|
|
|
A 0 PRESS STORE AUTO SHUT-OFF
|
|
|
|
|
|
Enter the data for the selected item. If an error is made during data
|
|
entry the CLR key can be used to erase single keys.
|
|
|
|
PRESS SEND to burn NAM. Phone will display PASS. If FAIL is displayed
|
|
you must repeat programming sequence.
|
|
|
|
To read the NAM (review) press SELECT 3 SEND. Enter RCL then the number
|
|
of the item that you wish to view. Press the CLR key to exit and return
|
|
to test mode.
|
|
|
|
TO VIEW THE SERIAL NUMBER OF THE UNIT BEING PROGRAMMED -
|
|
|
|
Press SELECT 4 SEND while in the Test Mode to display the phone's serial
|
|
number in decimal form. The manufacturer ID (172) will be displayed on
|
|
the top line while the remainder of the serial number will appear on the
|
|
bottom line Press the CLR key to return to the Test Mode display.
|
|
|
|
-------------------------------------------------------------------------------
|
|
|
|
|
|
DEFINITIONS:
|
|
|
|
XXX - Area Code or Prefix
|
|
|
|
XXXXXXX - Prefix & Suffix
|
|
|
|
XXXXXXXXXX - Area Code, Prefix, & Suffix
|
|
|
|
_ _ _ _ _ - Digits (One Line Per Digit [Sample To Left Is 5 Digits])
|
|
|
|
MIN* (Mobile Identification Number):
|
|
10 digit directory telephone number.
|
|
|
|
UNLOCK (Lock Code):
|
|
3 digit code to unlock radio (WARNING - The radio cannot
|
|
be unlocked if this code is forgotten).
|
|
NOTE: You can read this code by using the programming procedure.
|
|
|
|
SID* (Home System Identification):
|
|
5 digit number for assigned cellular system.
|
|
|
|
LU* (Local Use):
|
|
0 or 1. 1=local control option and responds to local control messages.
|
|
|
|
MIN MARK* 0 or 1. 1=home station sends extended address information
|
|
upon origination and page response.
|
|
|
|
IPCH* (Initial Paging Channel in Home):
|
|
3 digit number to identify the channel number of the first
|
|
paging channel when station is home.
|
|
|
|
ACCOLC* (Access Overload Class):
|
|
2 digit number to identify which overload class field controls
|
|
the access attempts.
|
|
|
|
PS* (Perferred System):
|
|
0 or 1. 1=Preferred system is System A
|
|
0=Preferred system is System B
|
|
|
|
GIM* (Group Identification Mark):
|
|
2 digit number which indicates how many bits of SID, starting
|
|
with the most significant, comprise the GIM.
|
|
|
|
AUX 0 or 1. 1=Auxiliary signal is enabled for horn relay.
|
|
External adapter must be used for this feature.
|
|
|
|
HANDS 0 or 1. 1=Handsfree feature is enabled.
|
|
External adapter must be used for this feature.
|
|
|
|
ALT LOCK (Alternate Lock Code):
|
|
3 digit lock code to be used with the partial lock feature.
|
|
This feature is active only with the GE CF-2000 and CF-2500
|
|
Carfone models.
|
|
This entry is ignored for GE CF-1000 Carfone models.
|
|
|
|
*These values are Cellular System dependent. Entering an
|
|
incorrect value will deny service on the system.
|
|
|
|
* * * * * * * * * * * * * * * W A R N I N G * * * * * * * * * * * * * * * * * *
|
|
|
|
When a cellular phone transmits, it sends its Electronic
|
|
Identification Number and its assigned telephone number
|
|
back to the cellular phone companys computer. This leaves
|
|
an electronic trail. If the phone is registered to you and
|
|
you change the phone number you run a risk of being tracked
|
|
by the Electronic Identification Number.
|
|
|
|
If the phone is not registered to you, you can be tracked by
|
|
the numbers you call frequently. It wouldn't be very smart to
|
|
phone home to see how the little woman is doing or check to
|
|
see if the latest software came on UPS. And remember, when
|
|
you use a cellular phone it goes out over the airways. This
|
|
means anyone with the know-how can listen to you. All some
|
|
people need is a juicy bit of information and a phone number
|
|
and you leave yourself open to all kinds of scams, blackmail,
|
|
and legal problems.
|
|
|
|
|
|
|
|
|
|
* * * M O R E * N O T E S * * *
|
|
|
|
|
|
Most cellular companys do not turn off the numbers that are not
|
|
in use. Better yet I do not know of a company that tracks numbers
|
|
that are not assigned. They seem to keep the low numbers filled
|
|
in. When someone turns in a phone they reassign that number
|
|
instead of a new number. If you put a number in your phone, use
|
|
a high number. Chances are it is not assigned to anyone. The
|
|
calls you make on a unassigned number usually will go unnoticed.
|
|
Better yet monitor the number you wish to use with a scanner for
|
|
a period of time to check for activity.
|
|
|
|
Happy foning.....
|
|
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
|
|
NETWORK 23 BBS, 24 HOURS, 1200/2400 BAUD, (402) 467-2474
|
|
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
|
|
|
|
This file was downloaded from......
|
|
|
|
|
|
_ _______ _____ _ _ ____ ____ _____
|
|
| | | _ | ___| | / /| __|| __ \ | ___|
|
|
| | | | | | | | | |/ / | |__ ||__| || |___
|
|
| | | | |_| | | | / | __|| _/ |___ |
|
|
| | | | _ | | | \ | | | \ | |
|
|
| | | | | | | |___| |\ \_| |___| |\ \_____| |
|
|
| |____| |_| |_|_______| \__________| \________|
|
|
| ____ |_______ _ __ _______
|
|
| | | | _ | | | \ | _ _|
|
|
| | | | |_| | | | | \ \ | | | |
|
|
| | | | _ | | | | |\ \| | | |
|
|
| | | | | | | |__| | | \ \ | | |
|
|
|_| |___| |_|________| \__| |_|
|
|
|
|
|
|
Call [UK] 081-656-1517
|
|
Worldwide +44 81 656 1517
|
|
24hrs!!
|
|
|
|
Downloaded From P-80 Systems 304-744-2253
|
|
|