110 lines
3.8 KiB
Plaintext
110 lines
3.8 KiB
Plaintext
AUDIOVOX 3100A,4100A,SP85A,CMT410A,BC55A,CTR1900,PT 300/BC55A,CTR1900
|
||
|
||
NOTES: These are single NAM units that have user programmable MIN & SIDH,
|
||
See below for user instructions.
|
||
The ESN prefix is 138 decimal, 8A hex (Toshiba)
|
||
These units have an excessive number of "security" features,
|
||
You MUST know the lock code or the "reprograming" code and you
|
||
may also need an "activation" code. Take care not to program
|
||
these options unless you're sure the numbers will not be mislaid.
|
||
There is a "back door" for the PT 300 portable, see end.
|
||
Audiovox: 516-231-6051/310-926-7758
|
||
|
||
NAM programing:
|
||
|
||
1. With the power turned on enter N N N FUNC # 1, where NNN is the three
|
||
digit lock code. The manufacturers default is 000. If a reprograming
|
||
code has been entered in step 26 (see below) this code must be used in
|
||
place of the three digit lock code. If "CODE ?" appears when the phone
|
||
is powered up then you must enter the 7 digit "Activation Code" before
|
||
entering programing mode, (see step 30).
|
||
|
||
2. The # key increments the step number.
|
||
|
||
3. The * key decrements the step number.
|
||
|
||
4. STO enters the data for each step.
|
||
|
||
5. You MAY directly access any step by pressing RCL followed by the step
|
||
number.
|
||
|
||
6. FUNC SND completes programing.
|
||
|
||
7. FUNC CLR exits programing mode.
|
||
|
||
PROGRAMING DATA:
|
||
|
||
STEP# #OF DIGITS/RANGE DESCRIPTION
|
||
|
||
01 10 DIGITS MIN (AREA CODE & PHONE NUMBER)
|
||
02 3 DIGITS LOCK CODE
|
||
03 00000 - 32767 SYSTEM ID
|
||
04 00 - 15 ACCESS OVERLOAD CLASS
|
||
05 00 - 15 GROUP ID (10 FOR USA)
|
||
06 0 OR 1 LOCAL USE MARK
|
||
07 0 OR 1 MIN MARK
|
||
08 0333 OR 0334 INITIAL PAGING CHANNEL
|
||
09 0 OR 1 PREFERRED SYSTEM
|
||
10 4 DIGITS STATION CLASS MARK
|
||
11 8 BINARY DIGITS FUNCTION 1, SEE NOTE 1 BELOW
|
||
12 8 BINARY DIGITS FUNCTION 2, SEE NOTE 2 BELOW
|
||
13 00 TO 31 HOURS POWER OFF TIMER (CTX 4000 ONLY)
|
||
14 000 TO 255 SECS NO CHARGE AIR TIMER DELAY
|
||
15 3 DIGITS CALL TIMER RESET CODE
|
||
16 - 25 00000 - 99999 SIDH INHIBIT # 1 THRU # 5
|
||
26 3 DIGITS NAM PROGRAMING CODE (LEAVE BLANK, SEE ABOVE)
|
||
27 - 29 NOT USED FUTURE USE
|
||
30 7 DIGITS ACTIVATION CODE (LEAVE BLANK, SEE ABOVE)
|
||
|
||
NOTES:
|
||
|
||
1. This is an eight digit binary field.
|
||
|
||
10000000 = CALL TIMER BEEP
|
||
01000000 = AUTO LOCK
|
||
00100000 = AUTO SYSTEM REDIAL
|
||
00010000 = CALL RESTRICTION
|
||
00001000 = 32 DIGIT DIALING CAPABILITY
|
||
00000100 = AUTO ANSWER
|
||
00000010 = AUTO ANSWER FOR DATA
|
||
11111000 = ALL OF THE ABOVE
|
||
|
||
|
||
2. As above but options are:
|
||
|
||
10000000 = HANDS FREE
|
||
01000000 = CONTINUOUS DTMF
|
||
00100000 = REPERTORY DIALING
|
||
00010000 = HORN ALERT
|
||
00001000 = ALLOWS 911 CALLING WHEN UNIT IS LOCKED
|
||
01101000 = ALL OF THE ABOVE
|
||
|
||
|
||
A/B SYSTEM SELECT:
|
||
|
||
FCN 0 4 DISPLAYS CURRENT MODE,
|
||
FCN 0 0 = PREFERRED/NON-PREFERRED,
|
||
FCN 0 1 = PREFERRED ONLY,
|
||
FCN 0 2 = HOME ONLY
|
||
FCN 0 3 = NON PREFERRED ONLY,
|
||
|
||
|
||
USER PROGRAMING OF MIN & SIDH
|
||
|
||
Press CLR followed by the new five digit SIDH and ten digit MIN.
|
||
Press FUNC 6. The new MIN will be displayed, hold 6 to display the SIDH.
|
||
|
||
|
||
"BACK DOOR" FOR PT-300
|
||
|
||
1. Remove the battery.
|
||
2. Remove the small black square access plate at the lower left of the
|
||
phone.
|
||
3. Place a 10k resistor between pins 4 and 5.
|
||
(Pin 5 is top right, pin 4 is center bottom)
|
||
4. Replace battery, power up phone and enter 0 0 0 FUNC # 1.
|
||
|
||
LOCK: Press LOCK. UNLOCK: Enter three digit code.
|
||
|
||
SYSTEM SELECT: F 0 4 shows current mode. F 0 0 = Pref/Non pref, F 0 1 = Pref
|
||
only, F 0 2 = Home Only, F 0 3 = Non pref only. |