183 lines
6.9 KiB
Plaintext
183 lines
6.9 KiB
Plaintext
$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
|
|
$ $
|
|
$ BLUE BOX PLANS! $
|
|
$ --------------- $
|
|
$ $
|
|
$ Edited and Uploaded by: $
|
|
$ $
|
|
$ $
|
|
$$$$$$$->The Spirit Of Radio<-$$$$$$$$$
|
|
$ $
|
|
$ Written by: $
|
|
$ $
|
|
$ Mr. America from Osuny BBS $
|
|
$ $
|
|
$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
|
|
|
|
This file will explain the construction, troubleshooting,
|
|
This design will make them last 10 months!!!!!! But
|
|
nevertheless, don'tforget to put in aswitch for on and off. Ok
|
|
let's build the two VCO'S andcalibrate the unit before we get to
|
|
the keyboard construction.
|
|
|
|
|
|
VCO CONSTRUCTION
|
|
|
|
TOOLS REQUIRED
|
|
1 ocilliscope(optional but not req)
|
|
1 Freq. counter (REQUIRED)
|
|
1 Volt meter " " "
|
|
Electronics tools (Pliers, drll, screwdrivers, etc.)
|
|
|
|
|
|
PARTS
|
|
|
|
R1 1.5K RESISTOR 5%
|
|
R2 1K RESISTOR 5%
|
|
C1 .1uf ELECTROLYTIC CAPACITOR 16VDC
|
|
C2 .01uf " " (MYLQR) 16VDC
|
|
C1 2207 VCO CHIP BY EXAR ELECTRONICS
|
|
|
|
Remember the above only says VCO#1 but the same is for VCO#2
|
|
|
|
R3-R4 150 OHM RESISTORS 5% .
|
|
C3-C4 .1 uf ELECTROLITIC CAPACITOR .
|
|
10VDC .
|
|
|
|
P1-P10 200K TRIMMER POT - 20 TURNS DIODES USED IN THE KEYBOARD
|
|
ARE 1N914 TYPE(40 OF THEM) & 13 SWITCHES FOR THE KEYBOARD SPST
|
|
MOMENTARY.
|
|
|
|
SPKR YOU CAN USE A TELEPHONE SPEAKER FOR THIS (IT WORKS BEST) BUT
|
|
REMEMBER TOTAKE OUT THE DIODE THAT IS CONNECTED ACCROSS IT.
|
|
|
|
|
|
IMPORTANT NOTES
|
|
|
|
1. DO NOT USE ANYTHING ELSE OTHER THAN A MYLAR CAPACITOR FORC2.
|
|
2. PINS 10,9,8 SHOULD BE TIED TOGETHER AND BE LEFT FLOATING.
|
|
3. ALL RESISTORS SHOULD BE 5%! NOTHING ELSE!
|
|
4. A TELEPHONE SPEAKER GIVES THE BEST RESULTS.
|
|
|
|
|
|
TROUBLE SHOOTING
|
|
|
|
By now you should have constructed the two VCO'S on a bread board
|
|
or anything that pleases you. Check for cold solder
|
|
joints,broken wires,polarity of the battery, etc. Before we
|
|
apply power to the VCO'S we have to adjust the pots for their
|
|
half way travel point. This is done by turning them 21 turns to
|
|
the right and then 10 turns to the left. Do the same for all ten
|
|
of them.
|
|
|
|
Now apply power to the unit check to see that you have power in
|
|
the chips by putting the positive lead of your volt meter on pin
|
|
7 andthe negative lead on pin 12. If you do not have anything
|
|
there turn off the unit and RECHECK THE WIRING.
|
|
|
|
When you get the right voltages on the chips, connect a diode to
|
|
a piece of wire (look at fig. 2 for the orientation of the diode)
|
|
from round to any pot at point T (look carefully at the schematic
|
|
for point T it is labeled T1-T10 for all pots). You should be
|
|
able to hear a tone, if not disconnect the lead and place the
|
|
speaker close to your ear and if you hear a chirp-like sound,
|
|
this means that the two VCO'S are working if you don't,
|
|
it means that either one or both of the VCO'S are dead. So in
|
|
this case it is always good to have an ocilloscope on hand.
|
|
Disconnect the speaker from the circuit and hook the ocilliscope
|
|
to 1 of the leads of the speaker & the ground from the scope to
|
|
the ground of the battery. Connect again the ground lead with the
|
|
diode connected to it from ground to any pot on the VCO that you
|
|
are checking and you should see a triangle wave if not turn the
|
|
pot in which you are applying the ground to until you see it.
|
|
When you do see it do the the same for the other VCO to makesure
|
|
it is working. (amplitude is about 2VAC). When you get the two
|
|
VCO's working you are set for the adjustment of the individual
|
|
spots.
|
|
|
|
|
|
ADJUSTMENT
|
|
|
|
Disconnect the speaker from the circuit and connect a freq.
|
|
counter (the positive lead of the counter to one of the speakers
|
|
leads that belongs to VCO#1 or connect it to pin 14.
|
|
|
|
Connect the negative lead to the battery negative and connect the
|
|
jumperlead with the diode from ground to pot number 1.T1 (the
|
|
first pot number 1 point T1). If you got it working you should
|
|
hear a tone and get a reading on the counter. Adjust the pot for
|
|
a freq. of 1700hz and continue doing the same for pots 2-5
|
|
except that they get different freqs. which are:
|
|
|
|
: $$$$$$$$$$$$$$ :
|
|
: $ $ :
|
|
: $ P1 1700hz $ :
|
|
: $ P2 1300hz $ :
|
|
: $ P3 1100hz $ :
|
|
: $ P4 900hz $ :
|
|
: $ P5 1500hz $ :
|
|
: $ $ :
|
|
: $$$$$$$$$$$$$$ :
|
|
|
|
Now disconnect the freq. counter from the speaker lead of VCO#1
|
|
or from pin (which ever you had it attached to at the beginning)
|
|
and connect it to the speaker lead of VCO#2 or to pin 14 of VCO#2
|
|
and make the same adjustments toP6-10.:
|
|
|
|
: $$$$$$$$$$$$$$$ :
|
|
: $ $ :
|
|
: $ P6 1100hz $ :
|
|
: $ P7 700hz $ :
|
|
: $ P8 900hz $ :
|
|
: $ P9 2600hz $ :
|
|
: $ P10 1500hz $ :
|
|
: $ $ :
|
|
: $$$$$$$$$$$$$$$ :
|
|
|
|
When you finish doing all of the pots go back and re-check
|
|
them.
|
|
|
|
|
|
KEYBOARD
|
|
|
|
IF YOU LOOK AT FIG-2 YOU WILL SEE THAT THE KEYS ARE
|
|
SIMPLE SWITCHES. CONNECTED TO A GROUND AND TWO DIODES ON THE
|
|
OTHER END. THESE DIODES ARE USED TO SIMPLIFY THE CONSTRUCTION OF
|
|
THE KEYBOARD BECAUSE OTHERWISE THE DISTRIBUTION OF THE GROUND
|
|
SIGNAL FOR BOTH VCO'S WOULD HAVE BEEN DONE MECHANICALLY. THE
|
|
DIODE WILL GO TO VCO#1 AND THE OTHER WILL GO TO VCO#2. FIG-3
|
|
SHOWS THE ARRANGEMENT OF THE KEYS ON THE KEYBOARD.
|
|
|
|
BELOW IS A TABLE THAT WILL HELP YOU CONNECT THE KEYS TO THE
|
|
REQUIRED VCO'SPOTS.
|
|
|
|
<------------------------------------->
|
|
< >
|
|
< (-FIG 2-) >
|
|
< >
|
|
<-----!-----!--------!--------!------->
|
|
< ! ! ! ! >
|
|
< TO ! TO ! FREQ ! FREQ ! KEY >
|
|
< POT ! POT ! OUT: ! OUT: ! >
|
|
< ON ! ON ! ! ! >
|
|
< VCO1! VCO2! ! ! >
|
|
<-----!-----!--------!--------!------->
|
|
< 1 ! 06 ! 1700hz ! 1100hz ! C >
|
|
< 2 ! 10 ! 1300hz ! 1500hz ! 0 >
|
|
< 1 ! 10 ! 1700hz ! 1100hz ! E >
|
|
< 4 ! 07 ! 0900hz ! 0700hz ! 1 >
|
|
< 3 ! 07 ! 1100hz ! 0700hz ! 2 >
|
|
< 3 ! 08 ! 1100hz ! 0900hz ! 3 >
|
|
< 2 ! 07 ! 1300hz ! 0700hz ! 4 >
|
|
< 2 ! 08 ! 1300hz ! 0900hz ! 5 >
|
|
< 2 ! 06 ! 1300hz ! 1100hz ! 6 >
|
|
< 5 ! 07 ! 1500hz ! 0700hz ! 7 >
|
|
< 5 ! 08 ! 1500hz ! 0900hz ! 8 >
|
|
< 5 ! 06 ! 1500hz ! 1100hz ! 9 >
|
|
< - ! 09 ! ------ ! 2600hz ! X >
|
|
< ! ! ! ! >
|
|
<------------------------------------->
|
|
|
|
REMEMBER THAT IN FIG-2 IT'S THE SAME FOR EACH KEY EXCEPT THE "X"
|
|
KEY, WHICH ONLY TAKES ONE DIODE.
|