119 lines
3.0 KiB
Plaintext
119 lines
3.0 KiB
Plaintext
***************************************
|
||
* How to make a *
|
||
* Portable Silver Box *
|
||
* *
|
||
* By: *
|
||
* The *
|
||
* Phone *
|
||
* Phantom *
|
||
* *
|
||
***************************************
|
||
|
||
|
||
This will tell you how to make a
|
||
portable silver box out of:
|
||
|
||
A Radio Shack touch tone pad
|
||
Some wire
|
||
A Soldering iron
|
||
And a SPDT switch
|
||
|
||
NOTE: You should have an I.Q. above
|
||
room tempature before attempting this.
|
||
Also, read all of this article before
|
||
starting.
|
||
|
||
WARNING: This may be hazardous to your
|
||
freedom.
|
||
|
||
1} Take off the plastic cover that
|
||
stores the batteries and remove the
|
||
screw that is in the center of the
|
||
batteries. Now use a screw driver to
|
||
pry open the box.
|
||
|
||
2} Now you should have the two halves
|
||
in your hands. On the side that has the
|
||
circuit board, it should be held by two
|
||
clips. Remove the circuit board now.
|
||
|
||
3} You should now be able to see the
|
||
back side of the keypad. Connecting the
|
||
the key pad and the circuit board is a
|
||
ribben cable. With the ribben ends
|
||
connected to the keypad away from you,
|
||
count from the left over four wires.
|
||
On the fourth wire, take and cut the
|
||
plastic on either side on the wire.
|
||
Then desolder it.
|
||
|
||
4} Now stare at the circuit board. Look
|
||
at the connections of the chip.
|
||
(SEE FIG.) There should be four pins
|
||
not connected to anything. On the
|
||
ninth pin (first row, first pin) solder
|
||
a 3 inch wire to it. The other end goes
|
||
to the left side of the spdt switch.
|
||
|
||
5} Go back to the cable. Solder a 2
|
||
inch to the ribben cable you just took
|
||
out. This is because it won't reach the
|
||
switch. The other end goes to right
|
||
side of the switch.
|
||
|
||
6} Now take a two inch wire and solder
|
||
it to the hole that the cable came out
|
||
of. Becareful not to get solder on the
|
||
other wires. Now take the other end and
|
||
solder it to the middle of the switch.
|
||
|
||
7} Make a hole in the top of the case
|
||
to put the switch through. And put it
|
||
back together.
|
||
|
||
THE FIGURE!!
|
||
OF THE CHIP.
|
||
|
||
THE PIN >9< 10 11 12 13 14 15 16
|
||
|
||
1 2 3 4 5 6 7 8
|
||
|
||
(Pretty cool eh?)
|
||
|
||
_______________________________________
|
||
|
||
Switch the switch left according to the
|
||
way you soldered it to make silver box
|
||
tones on the 3,6,9, and # keys.
|
||
Switch it to the right for a normal key
|
||
pad.
|
||
Switching it to the middle does
|
||
NOTHING!!!!
|
||
|
||
This silver is small enough to fit in
|
||
your pocket for phreaking at your
|
||
nearest pay phone or where ever.
|
||
|
||
This file is for information only
|
||
(RIGHT!) ha ha ha!
|
||
|
||
Written by:
|
||
|
||
The
|
||
Phone
|
||
Phantom
|
||
|
||
And a little (very little) help from...
|
||
|
||
Bubba
|
||
Hampton
|
||
Fortis The Camouflaged
|
||
Panis (?) Forest
|
||
|
||
Of...
|
||
Teenage
|
||
Wasteland
|
||
|
||
%^%^%^%^%^%^%^%^%^%^%^%^%^%^%^%^%^%^%^%
|
||
|
||
DOWNLOADED FROM P-80 SYSTEMS...... |