77 lines
3.6 KiB
Plaintext
77 lines
3.6 KiB
Plaintext
Here is the Bubble bobble wiring harness pinouts. Send corrections to:
|
|
djbarnes@eos.ncsu.edu
|
|
|
|
The 44 pin connector is as follows:
|
|
|
|
________________________________________________
|
|
|Component Side | |Solder Side |
|
|
|---------------|-------|-------|--------------|
|
|
|Ground | 1 | A |Ground |
|
|
|---------------|-------|-------|--------------|
|
|
|Video Red | 2 | B |Video Ground |
|
|
|---------------|-------|-------|--------------|
|
|
|Video Green | 3 | C |Video Blue |
|
|
|---------------|-------|-------|--------------|
|
|
|Video Sync | 4 | D |N/U |
|
|
|---------------|-------|-------|--------------|
|
|
|Speaker + | 5 | E |Speaker - |
|
|
|---------------|-------|-------|--------------|
|
|
|Key | 6 | F |Key |
|
|
|---------------|-------|-------|--------------|
|
|
|N/U | 7 | H |N/U |
|
|
|---------------|-------|-------|--------------|
|
|
|Coin Sw | 8 | J |N/U |
|
|
|---------------|-------|-------|--------------|
|
|
|Coin Meter | 9 | K |N/U |
|
|
|---------------|-------|-------|--------------|
|
|
|N/U | 10 | L |N/U |
|
|
|---------------|-------|-------|--------------|
|
|
|Service Sw | 11 | M |Slam Sw |
|
|
|---------------|-------|-------|--------------|
|
|
|1P sw | 12 | N |2P sw |
|
|
|---------------|-------|-------|--------------|
|
|
|N/U | 13 | P | |
|
|
|---------------|-------|-------|--------------|
|
|
|N/U | 14 | R | |
|
|
|---------------|-------|-------|--------------|
|
|
|1P right | 15 | S |2P right |
|
|
|---------------|-------|-------|--------------|
|
|
|1P left | 16 | T |2P left |
|
|
|---------------|-------|-------|--------------|
|
|
|N/U | 17 | U | |
|
|
|---------------|-------|-------|--------------|
|
|
|N/U | 18 | V | |
|
|
|---------------|-------|-------|--------------|
|
|
|N/U | 19 | W | |
|
|
|---------------|-------|-------|--------------|
|
|
|N/U | 20 | X | |
|
|
|---------------|-------|-------|--------------|
|
|
|Bubble Sw | 21 | Y |Bubble |
|
|
|---------------|-------|-------|--------------|
|
|
|Jump | 22 | Z |Jump |
|
|
|---------------|-------|-------|--------------|
|
|
|
|
|
|
The 36 pin connector is ground wired to 1-4, and A-D. Then wire +5V to 15-18, and S-V.
|
|
|
|
The power harness is as follows:
|
|
|
|
1 Ground
|
|
2 Ground
|
|
3 Ground
|
|
4 Ground
|
|
5 +5VDC
|
|
6 +5VDC
|
|
7 +5VDC
|
|
8 -5VDC
|
|
9 +12VDC
|
|
10 key
|
|
11 +12VDC
|
|
12 +12VDC
|
|
|
|
|
|
To use the board without a coin meter, you must insert a jumper across the points of J7
|
|
(located near IC 60, the large brown SIP IC near the G connector).
|
|
|
|
|