124 lines
6.3 KiB
Plaintext
124 lines
6.3 KiB
Plaintext
|
|
_--=PeEll=--_ (tm) on:
|
|
|
|
Delay Detonator
|
|
---------------
|
|
|
|
This phile shows how to build a simple electronic delay detonator for
|
|
almost any type of bomb that uses fire to detonate. This detonator can also be
|
|
modified to activate blasting caps for detonating Plastique etc. All of tha
|
|
parts are easily available at Radio Shack or other electronic stores. One
|
|
drawback of this detonator is that it costs about $10 in parts to make one. But
|
|
if you are rich or if you need more of a delay than a fuse can provide, this'll
|
|
do tha trick.
|
|
|
|
Parts List: Part # R.S. Cat. # Cost
|
|
2 Switching Diodes (1N914) 276-1122 $0.99
|
|
10K Resistor 271-034 $0.19
|
|
Relay Switch (6V) 275-004 $2.99
|
|
IC Timer 555 276-1723 $1.19
|
|
Mini LED 276-059 $0.99
|
|
Electrolytic capacitor (Size depends on delay desired)
|
|
Resistor (Size depends on delay desired) $0.19
|
|
Push button switch (any model)
|
|
2 9-Volt Batteries (Cheap, but new ones)
|
|
Small piece of breadboard approx $1.00
|
|
24 gauge solid core insulated wire
|
|
Soldering tools
|
|
Solar Igniters (electric matches available at hobby stores)
|
|
Mini Alligator clips (roach clips)
|
|
|
|
*** NOTE: Any SPDT 6 volt, 500 ohm, 12 mA relay can be used
|
|
instead of #275-004. Especially because #275-004
|
|
takes up a lot of room on tha board.
|
|
|
|
*** NOTE: Many of tha parts are sold in sets and you will
|
|
only need one. So, if you build more than one
|
|
detonator, you won't have to buy more of some
|
|
parts.
|
|
|
|
Schematic Diagram of Circuit. (solder everything on breadboard)
|
|
9 volt +
|
|
/|\ For values of R1 and C1 see notes
|
|
__________________|____________________ at tha end of this phile.
|
|
| | | |
|
|
| ____|8_______|4____ |
|
|
\ | | | D1
|
|
/ R1 | |3__________|\|_______o R x______________
|
|
\ | | |/| | E |
|
|
/ | 5 5 5 | | | o L x________ |
|
|
| | | \ | | A | - |
|
|
| | Integrated | / R2 | | Y | -----
|
|
|____________7| Circuit | \ _|__ | LED --- 9
|
|
| | | / /\ | | + | v
|
|
|____________6| |2___| D2 /__\ | | | o
|
|
| | | | | | A | l
|
|
| |___________________| | |____| | | t
|
|
| |1 |5 --- | | |
|
|
| C1 | | --- Switch | |_____|
|
|
|_______| (______|______|______________|___________|
|
|
+ | A= Alligator
|
|
----- R2=10K ohms Clips
|
|
---
|
|
- Ground (-) ** note: no connection between pins
|
|
3 & 4.
|
|
Tha bottom of tha relay has five pins. Tha pins here are marked with an
|
|
"x" or an "o" corresponding to tha schematic:
|
|
|
|
____________________
|
|
| |
|
|
| x o | RELAY SWITCH
|
|
| | (bottom base)
|
|
| |
|
|
| N o x | N= not used
|
|
|___________________ |
|
|
|
|
Tha alligator clips should be attached to tha breadboard using short
|
|
pieces of wire.
|
|
|
|
Tha longer lead on tha LED is tha positive lead. Make sure you hook it
|
|
up with tha right polarity. Same rule goes for tha capacitor.
|
|
|
|
Tha pins on tha 555 IC are numbered from tha top (side with paint & notch).
|
|
On tha left side tha read DOWN as 1,2,3,4. On tha right side tha read DOWN
|
|
8,7,6,5.
|
|
|
|
TEST:
|
|
Attach tha two batteries and clip roach clips together, tha LED will light.
|
|
Press and hold tha switch for 3 seconds. You should hear a click then tha
|
|
LED will go out. In a little while (depending on what capacitor and resis-
|
|
tor size you use), you should hear another click and tha LED will turn on
|
|
again. If this doesn't happen, you phucked up! Check your circuit care-
|
|
fully.
|
|
|
|
USING DETONATOR:
|
|
|
|
**** Read these instructions carefully before attempting this ****
|
|
|
|
If tha TEST worked, tha timer is ready to use. Attach two fresh batteries
|
|
and connect tha two roach clips. Allow time equivalent to your delay for
|
|
tha capactitor to charge. Now, press tha switch until tha LED goes out.
|
|
Now, quickly but carefully attach tha roach clips to tha Solar Igniter that
|
|
has been previously attached to your bomb. Then, get tha phuck out of
|
|
there!!! Once tha time delay expires, tha relay will open completing tha
|
|
second circuit and igniting tha Solar Igniter.
|
|
|
|
|
|
Tech Note: Tha values of R1 and C1 determine tha time delay. Tha greater
|
|
these values, tha longer tha delay. Tha equation to determine time delay
|
|
is as follows:
|
|
C1 (in farads) x R1 (in ohms)
|
|
Time (in seconds) = ---------------------------------
|
|
6
|
|
Tha value of C1 is in farads. Most capacitors are listed in micro-
|
|
farads. To use tha formula, divide tha number of microfarads by 1,000,000.
|
|
|
|
Example: If you use a 500 microfarad capacitor for C1 and a 10
|
|
megaohm resistor for R1, you would have a delay of 14
|
|
minutes (833 seconds).
|
|
|
|
|
|
***** Disclaimer time. If you phuck this up and die, It's not my fault!!!!
|
|
|
|
_--=PeEll=--_ (tm)
|