94 lines
4.1 KiB
Plaintext
94 lines
4.1 KiB
Plaintext
Making Impovised Proximity Mines
|
|
By:MassExodus
|
|
|
|
|
|
All of these Files are for informational purposes only and any trouble
|
|
That may result from reading this file is your sole responsiblity and the
|
|
author or his ISP may be held liable for any legal trouble that may ensue.
|
|
Devices such as this can cause serious harm.
|
|
|
|
Have you ever played any of the James Bond series games or perhaps
|
|
watched one of the films and wondered how cool it would be to have some of his
|
|
little toys? While if you have, this article is for you because today i will be
|
|
teaching you how to make an Proximity Mine.
|
|
|
|
What you'll need.:
|
|
|
|
1 Motion Sensor\alarm Easily found at any local Radio Shack. now this will run you about
|
|
$9.99 But don't cheap out.(you'll be unpleasently suprised if it blows up in your face because of bad workmanship,)
|
|
|
|
Some Gunpowder-The amount varies with how big you want the effect to be.(Taken from shells
|
|
or perhaps fireworks. if you don't have access to plain)
|
|
|
|
1 Glass Test tube(regular size)-if you can't find a glass test tube this can be substituted
|
|
With any container able to hold the amount of gun powder you need. i just like the glass
|
|
because its pretty.
|
|
|
|
A length or wire or several alligator clips.
|
|
|
|
1 Igniter.(These can be found in hobby shops that sell rocketry supplies, Now make sure you
|
|
only buy the one time ignitors the kind that are like to little metal pins and a strip of
|
|
paper. and not the mechanical type)
|
|
|
|
|
|
Now that you have the supplys Lets move onto the Fun part.
|
|
|
|
---:::-Construction
|
|
|
|
The first thing you should do is play with the motion sensor to make sure it works right
|
|
and to figure out how it works.
|
|
|
|
You need to open the case without damaging ANYTHING!!! and find where the speaker
|
|
that the alarm uses when it goes off. If your not sure which peice is the speaker you
|
|
shouldnt be doing this...
|
|
|
|
Now that you've found the speaker. Look at it and the wires that connect it to the Device.
|
|
There will be two wires now Take Something and make a good cut at the end of the wires about
|
|
1\4 of an inch to where they connect to the speaker.Now that you've disconnected the speaker
|
|
take this wire and strip a bit From the ends so you have about 1\4 inch bare wire at the end.
|
|
|
|
Find a way to get some of the wire on the outside of the case.(Drill or cut a hole if you have to.)
|
|
The case doesnt really matter anyway. Now reclose the case.
|
|
|
|
Now if you have the iq of a houseplant and have done this correctly it shoud look like this.
|
|
|
|
I I <-Wires
|
|
I I
|
|
----------- <-Case
|
|
|
|
Take some alligator clips and clip them to each of the little metal prongs on the bottom of
|
|
The ignitor(one Clip for Each Duh.!) and clip the last two clips onto the two exposed wires
|
|
on the outside of the case.
|
|
|
|
It should look like this: --------------
|
|
[ ignitor ]
|
|
--------------
|
|
I I
|
|
hhHHH HHHhh
|
|
I I
|
|
I I
|
|
I I
|
|
hhHHH HHHhh
|
|
I I
|
|
I I
|
|
-------------- <--Case
|
|
|
|
Thats your Proximity Detonator.
|
|
|
|
Now it will probubly be a good idea to check the functionality of your device by using
|
|
only a ignitor and No explosive(Just to be Sure).
|
|
|
|
Now just Put the Ignitor into you container(with the Explosive) and close the lid\cap\whatever, just make
|
|
sure that the wires don't get severed!, and you have made your very own proximity mine.
|
|
When your ready to use Just attach the Device to you container. and arm it like you would if
|
|
it were still an alarm.
|
|
|
|
|
|
How it works.
|
|
|
|
Well supposing you didn't get the kind of alarm that beeps before its active. once the
|
|
motion detector is set off. The electircal charge Which would normaly make the alarm sound
|
|
is sent to The ignitor and that sets off the boom. don't get hurt.
|
|
|
|
|
|
-----MassExodus------]-{ |