149 lines
8.0 KiB
Plaintext
149 lines
8.0 KiB
Plaintext
|
||
|
||
The following article has been taken from issue 13 of TRSLINK Magazine, edited
|
||
by Luis M. Garcia-Barrio and Peter Besenbruch. The article is being re-
|
||
distributed with permission and may continue to be distributed freely provided
|
||
that no fee is charged for its distribution (excepting connect time fees for
|
||
telecommunications services, or a maximum fee of $1.50 to cover the cost of
|
||
computer media).
|
||
|
||
Linefeeds have been added to the file, as well as a left margin (eight spaces).
|
||
|
||
|
||
|
||
Modem Noise Killer (alpha version)
|
||
|
||
In this project, with some basic tools and a few
|
||
components from Radio Shack, you should be able to cut the
|
||
noise/garbage that appears on your computer's screen. I started
|
||
this project out of frustration at using a US Robotics 2400
|
||
baud modem and getting a fair amount of junk when connecting at
|
||
that speed. Knowing that capacitors make good noise filters, I
|
||
threw this together.
|
||
|
||
It is very easy to build, however conditions may be
|
||
different due to modem type, amount of line noise, old or new
|
||
switching equipment (Bell's equipment), etc. So it may not work
|
||
as well for you in every case. If it does work, or if you've
|
||
managed to tweek it to your computer/modem setup I'd like to
|
||
hear from you. I'd also appreciate any of you electronic
|
||
wizzards out there wanting to offer any improvements. Let's
|
||
make this work for everyone!
|
||
|
||
Please read this entire message and see if you understand
|
||
it before you begin.
|
||
|
||
OK. This is what you'll need from Radio Shack:
|
||
|
||
a) 1 #279-374 Modular line cord if you don't already have one.
|
||
You won't need one if your phone has a modular plug in its
|
||
base. $4.95
|
||
|
||
b) 1 #279-420 Modular surface mount jack (4 or 6 conductor)
|
||
$4.49
|
||
|
||
c) 1 #271-1720 Potentiometer. This is a 5k audio taper variable
|
||
resistor. $1.09
|
||
|
||
d) 1 #272-1055 Capacitor. Any non-polarized 1.0 to 1.5 uf cap
|
||
should do. Paper, Mylar, or metal film caps should be used,
|
||
although #272-996 may work as well. (272-996 is a non-
|
||
polarized electrolytic cap) $.79
|
||
|
||
e) 1 100 ohm resistor - quarter or half watt. $.19
|
||
|
||
f) 1 #279-357 Y-type or duplex modular connector. Don't buy
|
||
this until you've read the section on connecting the Noise
|
||
Killer below. (A, B,or C) $4.95
|
||
|
||
First, pry open the modular block with a screwdriver.
|
||
Inside you'll find up to 6 wires. Very carefully cut out all
|
||
but the green and red wires. The ones you'll be removing should
|
||
be black, yellow, white, and blue. These wires won't be needed
|
||
and may be in the way. So cut them as close to where they enter
|
||
the plug as possible. The other end of these wires have a spade
|
||
lug connector that is screwed into the plastic. Unscrew and
|
||
remove that end of the wires as well.
|
||
|
||
You should have two wires left. Green and red. Solder one
|
||
end of the capacitor to the green wire. Solder the other end of
|
||
the capacitor to the center lug of the potentiometer (there are
|
||
three lugs on this critter). Solder one end of the resistor to
|
||
the red wire. You may want to shorten the leads of the resistor
|
||
first. Solder the other end of the resistor to either one of
|
||
the remaining outside lugs of the potentiometer. It doesn't
|
||
matter which.
|
||
|
||
Now to wrap it up, make a hole in the lid of the mod block
|
||
to stick the shaft of the potentiometer through. Don't make
|
||
this hole dead center as the other parts may not fit into the
|
||
body of the mod block if you do. See how things will fit in
|
||
order to find where the hole will go.
|
||
|
||
Now that you've got it built you'll need to test it. Twist
|
||
the shaft on the potentiometer until it stops. You won't know
|
||
which way to turn it until later. It doesn't matter which way
|
||
now. You also need to determine where to plug the Noise Killer
|
||
onto the telephone line. It can be done by one of several ways:
|
||
|
||
1) If your modem has two modular plugs in the back, connect the
|
||
Noise Killer into one of them using a line cord. A line cord
|
||
is a straight cord that connects a phone to the wall outlet.
|
||
|
||
2) If your phone is modular, you can unplug the cord from the
|
||
back of it after you're on-line and plug the cord into the
|
||
Noise Killer.
|
||
|
||
3) You may have to buy a Y-type modular adaptor. Plug the
|
||
adaptor into a wall outlet, plug the modem into one side and
|
||
the Noise Killer into the other. Call a BBS that has known
|
||
noise problems. After you've connected and garbage begins to
|
||
appear, plug the Noise Killer into the phone line as
|
||
described above. If you have turned the shaft on the
|
||
potentiometer the wrong way you'll find out now. You may get
|
||
a lot of garbage or even disconnected. If this happens, turn
|
||
the shaft the other way until it stops and try again. If you
|
||
don't notice much difference when you plug the Noise Killer
|
||
in, that may be a good sign. Type in a few commands and look
|
||
for garbage characters on the screen. If there still is,
|
||
turn the shaft slowly until most of it is gone. If nothing
|
||
seems to happen at all, turn the shaft slowly from one side
|
||
to the other. You should get plenty of garbage or
|
||
disconnected at some point. If you don't, reread this
|
||
message to make sure you've connected it right.
|
||
|
||
*** END OF ORIGINAL FILE ***
|
||
|
||
ADDITION TO ORIGINAL FILE - 2/29/88
|
||
|
||
Mike McCauley - CIS 71505,1173
|
||
|
||
First, a personal recomendation. _THIS WORKS!!!_ I have
|
||
been plagued with noise at 2400 for some time. I went round and
|
||
round with Ma Bell on it, and after they sent out several
|
||
"repair persons" who were, to be kind, of limited help in the
|
||
matter, I threw in the towel. I saw this file on a board up
|
||
east a few days ago, and thought I'd bite. Threw the gismo
|
||
together in about 10 minutes, took another five to adjust the
|
||
pot for best results on my worst conection, and guess what? No
|
||
more worst connecion! A few pointers:
|
||
|
||
1) The pot need not be either 5K or audio taper. I used a 10K
|
||
15 turn trim pot. Suggest you use what is handy.
|
||
|
||
2) I used 2MFD's of capacitance (two 1MFD's in parallel) Two
|
||
R.S. p/n 272-1055 work fine. Remember that about 90 Volts
|
||
will appear across red & green at ring, so the caps should
|
||
be rated at 100VDC+.
|
||
|
||
3) I ended up with a final series resistance value (100 ohm +
|
||
pot) of 2.75K. I speculate that one could probably use 2MFD
|
||
and a fixed 2.7K resistor and do the job 90% of the time.
|
||
The adjustment of the pot is not very critical. Changes of
|
||
+/- 1K made little difference in the performance of the
|
||
circuit.
|
||
|
||
Hope it works as well for you as it did for me.
|
||
|
||
Mike McCauley
|
||
|