74 lines
3.5 KiB
Plaintext
74 lines
3.5 KiB
Plaintext
|
||
***********************************************************
|
||
*
|
||
MEMBER NAME: WHITE2 *
|
||
*
|
||
***********************************************************
|
||
|
||
/-/-/-/-/-/-\-\-\-\-\-\
|
||
<:-\-White Box Plans-\-:>
|
||
\-\-\-\-\-\-/-/-/-/-/-/
|
||
|
||
|
||
(>Introduction<)
|
||
|
||
This article will tell you how to take a normal touch tone
|
||
keypad and convert it to a portable unit. First of all, the tones made by
|
||
a touch on telephone are not single tones, they are a combination of two
|
||
tones, making 'DTMF' (Dual tone Munlti-frequency). The normal tone
|
||
telephone dials 12 different signals (see bulletin on Silver Boxes). The
|
||
power required by a keypad is about 25 volts, but they will work with as
|
||
little as 15, thereby allowing the use of
|
||
|
||
As you may have gussed, they are also designed to operate with a
|
||
telephone type speaker (and phoneline), and not the standard 8-OHM speaker
|
||
which needs to be used for adequate vtlume. To accomplish this we use a
|
||
matching transformer, this is one of those miniature ones available at
|
||
radio shack. Enough of the theory, no
|
||
|
||
|
||
(>Phone Modification Instructions<)
|
||
|
||
You will need:
|
||
|
||
<1> Touch Tone Keypad
|
||
<2> Minature 1000 to 8OHM transformer
|
||
(Radio Shack # 273-1380)
|
||
<3> A standard 8-OHM speaker
|
||
<4> Two 9-VOLT Radio Bateries
|
||
<5> Two 9-VOLT clips
|
||
<6> A case to put it all in (optional)
|
||
|
||
o A few construction notes, I suggest that you solder and tape all
|
||
connections. It is also important to read this entire article before
|
||
attemping to construct this.
|
||
|
||
First, connect the red wire of the transformer to either
|
||
terminal on the speaker. Now connect the white wire from the transformer
|
||
to the other terminal speaker. Next, connect the red (positive) wire of
|
||
one battery clip to the black wire on the other battery clip. Now connect
|
||
the remaining red wire on the second battery clip to the green wire from
|
||
the touch tone pad. Connect the blue wire from the touch tone pad to the
|
||
orange-and-black striped wire from the touch to black lead from the first
|
||
battery clip. You have now finished the power connection to the keypad.
|
||
|
||
Next, connect the black wire from the keypad to the blue wire on
|
||
the transformer. Now connect the red-and-green striped wire from the
|
||
keypad to the green wire on the transformer. The black wire on the
|
||
transformer should not be connected to anything, along with quite a few
|
||
wires from the keypad. The connection of the keypad is now complete. All
|
||
you have to do is connect two nine volt batteries to the battery clips,
|
||
and you'll be ready to go. You may want to mount it in a case for easy
|
||
portability.
|
||
|
||
(>Use of the White Box<)
|
||
|
||
To bring the White Box to its full potential Silver box
|
||
modifications should be made to this unit, thus allowing complete remote
|
||
phreaking. When none of the buttons are pressed, this unit uses NO power,
|
||
thereby eliminating the need for a power s
|
||
|
||
|
||
______________________________________________________________________________
|
||
____________________________________-END-_____________________________________
|
||
|