120 lines
4.6 KiB
Plaintext
120 lines
4.6 KiB
Plaintext
|
||
|
||
Title: Plans For construction of a Sword Box.
|
||
Date: 1/13/88
|
||
Time: 7:24 pm
|
||
|
||
|
||
|
||
|
||
[-.-][-.-][-.-][-.-][-.-][-.-][-.-][--.-][-.-][-.-][-.-][-.-][-.-][-.-][-.-]
|
||
[-.-] [-.-]
|
||
[-.-] Completely reorganized plans for the [-.-]
|
||
[-.-] S W O R D B O X [-.-]
|
||
[-.-] [-.-]
|
||
[-.-] By Grim Reaper/STS [-.-]
|
||
[-.-] [-.-]
|
||
[-.-] Alternate Mindlink [713] [489-7779] [-.-]
|
||
[-.-] Celestial Woodlands [713] [580-8213] [-.-]
|
||
[-.-] [-.-]
|
||
[-.-][-.-][-.-][-.-][-.-][-.-][-.-][--.-][-.-][-.-][-.-][-.-][-.-][-.-][-.-]
|
||
|
||
|
||
|
||
Introduction:
|
||
After such a great gfile header, I think you deserve an explanation. The
|
||
sword box is just essentially a bud/beige/day-glo box with enhancements and
|
||
modifications. The structural differences in the sword box make it better
|
||
however, and thus safer for you to use. As always, read through the file
|
||
once before starting.
|
||
|
||
|
||
Equipment needed for construction of Sword Box
|
||
______________________________________________________________________________
|
||
|
||
1 7x3x4 box [experimenters, or project] made of plastic
|
||
2 insulated large alligator clips [might need backups]
|
||
2 reels of different colored wire
|
||
1 3 or 4 volt lightbulb, smaller voltage [1-1.5] will also be fine
|
||
A strong power drill [Sears or something] with a small [5/64] bit
|
||
Rubber based electric tape
|
||
1 common phone plug interface [plug,modulator,etc.] preferably wall-based
|
||
|
||
______________________________________________________________________________
|
||
|
||
|
||
STEP 1.
|
||
Okay, this is the first part. Make sure you are familiar with BELL tech.
|
||
phone voltage, connecting, tones,etc. so that you won't stumble and mess up.
|
||
First take the box, cut off the bottom, or open it up. Now drill two holes
|
||
on one of the ends, like this:
|
||
|
||
Top
|
||
-----------------------
|
||
- -
|
||
- o o -
|
||
- -
|
||
_______________________
|
||
Bottom
|
||
|
||
Thread about eight inches of wire through the holes, so that four inches
|
||
are on the outside, and four are inside. Solder the alligator clips onto
|
||
the ends of the outside part of the wire.
|
||
|
||
|
||
STEP 2.
|
||
Take the phone interface, and set it aside. Drill two holes close to each
|
||
other into the top of the box [top right corner] where the alligator clips
|
||
are facing you. Glue or tape the light bulb between these two points. Now
|
||
thread one wire through a hole and connect to the POSITIVE part of the light
|
||
bulb. Thread another wire throught the other hole and connect it to the
|
||
NEGATIVE part of the light bulb. The other part of the wires should be inside
|
||
the box [gone through the hole].
|
||
|
||
|
||
STEP 3.
|
||
Take the drill and drill two holes RIGHT next to each other in the middle
|
||
of the top of the box. Take the phone interface and snip off the black and
|
||
yellow wires [not needed]. Thread the remaining two wires into the holes
|
||
you just drilled, with red on the left, and green on the right. Glue
|
||
or tape the interface to the box. The two wires should be going inside
|
||
the box.
|
||
|
||
|
||
STEP 4.
|
||
Here comes the tricky part. Flip the box over and look inside. There should
|
||
be six wires coming from outside through holes. Now connect the red wire
|
||
from the phone interface to the red wire that has the alligator clip on it.
|
||
Wire the green phone interface wire to the green wire with the alligator clip
|
||
on it.
|
||
To the connection of the two red wires, connect the wire from the light bulb
|
||
that is bound to the positive side of the bulb.
|
||
To the connection of the two green wires, connect the wire that touches the
|
||
negative part of the bulb.
|
||
|
||
Now look over all the connections and electric tape them. Make sure it's
|
||
secure. At last, close or fix the bottom of the box back on.
|
||
|
||
|
||
|
||
|
||
Usage:
|
||
|
||
Use as a normal bud/beige/day-glo box. When the phone connects, the light
|
||
bulb will light up [of course]. In place of the light bulb, you could later
|
||
install a tone generator to cycle a 2600 Hz tone or something. Do what you
|
||
want.
|
||
|
||
|
||
|
||
|
||
Happy Boxing!
|
||
|
||
Grim Reaper
|
||
[11/22/87]
|
||
|
||
The Phraudulent Phortress (713)879-7084
|
||
|
||
[G-File]:[2]:[Box Plans]:[?/Help]:
|
||
/s
|
||
|