73 lines
3.5 KiB
Plaintext
73 lines
3.5 KiB
Plaintext
|
||
++----------------------++
|
||
| |
|
||
| INTRODUCING |
|
||
| THE NOISE BOX |
|
||
| |
|
||
++----------------------++
|
||
| Brought To You By: |
|
||
| Doctor Dissector |
|
||
++--------------------++
|
||
| PHORTUNE 500 |
|
||
+--------------------+
|
||
|
||
NOTE: This document was intended for informational purposes ONLY, the author
|
||
and Phortune 500 do not endorse or support any illegal action presented
|
||
here; the only motivation for writing of this document is purely for
|
||
educating the general public. Any actions by the readers of this paper
|
||
will not be held responsible against the author and Phortune 500.
|
||
|
||
|
||
Introduction:
|
||
So, that enemy has finally done it. They have really ticked you off so
|
||
bad that you are going to get them back for it. I mean bad. Allright then, you
|
||
have a mind-set for the noise-box then.
|
||
What is a noise-box? It is a device you can attach to a victim's
|
||
phone line so that an abnormal amount of noise will be present on the line at
|
||
all times, which would make data transmissions almost impossible and voice
|
||
communications annoying, to say the least. So, now that you know what it is,
|
||
let us go about the steps of building one.
|
||
|
||
|
||
Building/Installing A Noise-Box:
|
||
Materials:
|
||
1 5k Potentiometer/10k Potentiometer 15 turn
|
||
1 1.0-1.5 uf Capacitor, non-polarized, 100vdc+
|
||
1 100 ohm, 1/2 or 1/4 watt resistor
|
||
2 Alligator clips
|
||
1 Beige box
|
||
1 Green base (closest to victim's house)
|
||
|
||
Procedure:
|
||
1) Solder one end of the capacitor to the middle lug of the pot.
|
||
2) Solder one end of the resistor to either remaining end on the pot.
|
||
3) Attach alligator clips on the other ends of the capacitor and resistor.
|
||
4) Go to the green base by the victim's house.
|
||
5) Open the green base to expose the terminal block.
|
||
6) With a beige box, locate the victim's line using ANI.
|
||
7) Remove the beige box and remember which terminal it was.
|
||
8) Take your noise box and hook the capacitor's clip on the tip of the
|
||
victim's terminal. (tip - left side)
|
||
9) Hook the resistor's clip on the ring of the victim's terminal.
|
||
(ring - right side)
|
||
10) Put the beige box back onto the terminal and press a digit. Listen
|
||
for any noise, and slowly adjust the pot until you hear the greatest
|
||
amount of line-noise. Stop adjusting the pot, remove the beige box,
|
||
and close the green base. You are done!
|
||
|
||
|
||
Closing:
|
||
Pretty nifty, huh? Well, I know there are easier ways of doing this, and I
|
||
will experiment a bit to find the best combination, so you won't have to go
|
||
around adjusting pots and shit. Well, enjoy, and don't go doing it around my
|
||
house... hehehe
|
||
|
||
Doctor Dissector
|
||
|
||
Give these bitchin' BBS's a call, or if you want to contact me.....
|
||
===================================================================
|
||
The Andromeda Strain - WCCA HQ - 1200/2400 ----------- 619-566-7093
|
||
Electric Dreams - PhortuneNET 500 Node - 1200/2400 --- 619-739-9564
|
||
The Phrozen Phorest - Call It NOW! - 1200 ------------ 619-484-3508
|
||
|
||
DOWNLOADED FROM P-80 SYSTEMS...... |