189 lines
6.9 KiB
Plaintext
189 lines
6.9 KiB
Plaintext
This is the most commonly used chip on the market today so I
|
||
will try to make this as Simple as possible! the following is
|
||
a Diagram of the MB8719 Chip Used in all the New radios!
|
||
|
||
|
||
ÚÂÄÄ¿ ÚÄÄÄ¿
|
||
2nd amp o ³o ÀÄÙ o³ Grnd - vss
|
||
2nd amp in ³o M o³ F in
|
||
pin4 out ³o B o³ P0
|
||
inv up amp ³o 8 o³ P1
|
||
PD output ³o 7 o³ P2
|
||
lock det. ³o 1 o³ P3
|
||
ref{Q-out ³o 9 o³ P4
|
||
ref{Q-in ³o o³ P5
|
||
VDD - 9v ³o o³ divide/inverter
|
||
ÀÄÄÄÄÄÄÄÄÄÙ on input P6
|
||
|
||
|
||
Because of Pin 10, the chip downmixer can be referenced to
|
||
two different frequencies with the same 40 channel result!
|
||
In radios using the 11.11258 crystal, Pin 10 is Grounded
|
||
causing the Chip to go to full up-count. In this case lifting
|
||
Pin 10 from Ground will cause the radio to cover 120 channels
|
||
with the highest frequency being 27.445 MHz. The other
|
||
chassis that have pin 10 high, use a 11.3258 MHz. crystal for
|
||
reference. In these Chassis, by grounding pin 10 the Radio
|
||
goes up in frequency by a similar range. The truth table is
|
||
based on the 11.3258 MHz. crystal reference.
|
||
|
||
|
||
CLARIFIER:
|
||
Because of the various versions of the 8719 Chassis i will
|
||
Use the President Mckinely as a Example. this conversion is
|
||
for all 8719 Chassis. The following covers all President ,
|
||
Most Cobras , SBE, Stalker, Realistic and other radios with
|
||
a Uniden Chassis.
|
||
|
||
1. Cut out D-36.
|
||
|
||
2. Remove R-187. this applies voltage to the circuit in the
|
||
transmit and will cause tracking problems if not removed.
|
||
|
||
3. Leave the center wire from the Clarifier alone!
|
||
|
||
4. Follow the orange wire from the clarifier control and
|
||
remove it from where it connects to the radio. (this point
|
||
will vary with different radios.)
|
||
|
||
5. Connect this wire a (longer length may be added) to pin 3
|
||
of IC-5. (located bottom of board on left side with the radio
|
||
facing front.) This supplies constant 8 volts from the
|
||
Regulator.
|
||
|
||
|
||
6. Follow the red wire from the clarifier control to the
|
||
point where it is connected to the chassis.
|
||
|
||
7. Connect this wire to ground through a 47 ohm resistor
|
||
in series with the wire or through a 1N914 signal Diode with
|
||
cathode to ground. this is important because it isolates the
|
||
regulated supply from the ground. In Case of Regulator
|
||
failure the diode or resistor will act as a Fuse to protect
|
||
things. this gimmick can save you a lot of problems and grief
|
||
so use it!
|
||
|
||
8. Slide can be increased by lifting the Anode of the
|
||
Varactor diode and add a Series 5.6 - 8 uh choke to Ground.
|
||
if more slide is needed either purchase a Super varactor or
|
||
go to your local TV Shop and Scrap one from a Vhf Tuner!
|
||
|
||
THIS DIAGRAM COVERS NEARLY ALL UNIDEN CHASSIS WITH THE 8719
|
||
|
||
ÚÄ¿
|
||
³ ³³-47 ohm added
|
||
ÚÅ¿À´ to grnd.
|
||
ÀÄÄ¿
|
||
À¿
|
||
Clarifier> o
|
||
o <ÄÄÄÄÄÂÄÄÄÅÄÄ>ÄÄ¿
|
||
ÚÄÄÄÄÄÄÄÄ> o ³ ÅÂ
|
||
³ ÚÁ¿ ³³ D36
|
||
apply constant ³ ³ ÃÙ
|
||
8 volt source at ÀÂÙ ³
|
||
this pin. o<Ä¿ o<Ä¿
|
||
³ ³
|
||
remove this
|
||
resistor and diode
|
||
(D36 & R187)
|
||
|
||
|
||
TECH NOTE:
|
||
In some Washingtons and Robyns as well I have found pin 10
|
||
was wire-wrapped under the chip to ground. Suppliers of
|
||
Conversion kits tell you you have to replace the chip! This
|
||
is false! Carefully heat the pin and push the ground wire
|
||
off the pin. cut the wire as close as possible to the chip
|
||
and proceed with the Conversion! (Another first from HCS)!
|
||
|
||
1. replace the removed Crystal with a 11.3258 MHz. Crystal
|
||
NOTE:
|
||
if you use a Uniden Stock crystal (11.3258) which is cut to
|
||
a higher PF. load than the Special Conversion Crystals you
|
||
may have a Difficult time to recenter the Clarifier! Be Aware
|
||
|
||
2. Switch Method 1 will start up coverage from 27.605 and go
|
||
to 28.045
|
||
|
||
|
||
3. Switch method 2 will give normal operation in the center
|
||
postion 2 - 27.455 - 27-605 and in position 3 will give from
|
||
27.605 - 28.045. This switch is intended for amateur use when
|
||
converting the radio to 10 Meter operation.
|
||
|
||
|
||
SWITCH 1 ÚÄÄÄÄÄÄÄÄÄ> to Chip VCC+ Supply
|
||
ÚÅÄÄÄÄÄÄ¿
|
||
ÚÄÄÄÄijo o³
|
||
ÚÁ¿ ³ ³
|
||
1N914 ÃÄ´ ³o Úo³
|
||
ÀÂÙ ÚÄÄÅÄÄÄÄÄÙ ³
|
||
ÀÄÄÙ ³o o³ÄÄÄÄ> To Pin 12 at after resistor
|
||
ÀÄÄÄÄÄÄÄÙ is has been added
|
||
Switch can be SPST or DPDT
|
||
|
||
|
||
|
||
SWITCH 2 ÚÄÄÄÄ> to pin 10
|
||
ÚÄÄÄÄÄÅÄÄ¿
|
||
ÚÄÄÄÄÄijo ³ o³ÄÄ¿
|
||
³ ³ ³ ³ ÚÁ¿
|
||
³ ÚÄijo ÀÄo³ ³ ³
|
||
³ ³ ³ ³ ÀÂÙ
|
||
³ ³ ³o o³ÄÄÁÄÄÄÄ> To Board Ground
|
||
³ ³ ÀÄÄÄÄÄÄÄÄÙ
|
||
³ ³
|
||
³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ> to pin 11
|
||
³
|
||
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ> to pin 12
|
||
|
||
MB8719 Coverage from Channel 45 - 99+ with one switch &
|
||
diode Protect.
|
||
|
||
10 METER CONVERSION:
|
||
Replace Crystal with 11.8391 MHz. Covers Phone band Above
|
||
29.5 MHz. Using a 11.660 crystal for 28.0 to above 29.0 MHz.
|
||
|
||
MB8719 Tuneup:
|
||
Connect a Freq. Counter to TP1
|
||
Put the Radio on Channel 20
|
||
In the USB mode adjust CT3 for 35.0075 MHz.
|
||
In radios with choke added to Clarifier set control at 3:00
|
||
clock position.
|
||
Switch to LSB mode and adjust L19 for a Freq. of 35.0025
|
||
Switch to AM Mode and adjust L20 for 35.0050 MHz.
|
||
Peak Transmitter by tuning L26, L27, L29, & L36
|
||
AM Power is adjusted for VR-6
|
||
SSB ALC is adjusted with VR-7
|
||
To Increase Modulation Cut the collector of TR-32
|
||
Touch up Recieve stages if converting to 10 Meters
|
||
|
||
SUPER TRICK:
|
||
If you Need More bandwidth connect a Varactor to the coil
|
||
side of the cut trace and the cathode of the VCO Chip side.
|
||
Retune the VCO coil for operation over the entire range!
|
||
Cut The trace from the VCO coil going to pin 6 of the VCO
|
||
And Do the conversion described Above.
|
||
|
||
All users who register there Copies of These conversions will
|
||
recieve for $5.00 complete Written Documents and Complete
|
||
Drawings with much more Information and tricks and More
|
||
Updates on the Export radios & Conversions for FM and Much
|
||
More. if you Use my Conversions Please send a Donation of not
|
||
Less Than $10.00 Check or Money order to:
|
||
|
||
Carl D. Henson
|
||
315 Summit Ave.
|
||
Springfield, Il. 62704
|
||
(217) 523-0252
|
||
|
||
These Conversions cannot be Reproduced in any form of Media
|
||
without my Written Consent! This is shareware not Public
|
||
Domain! No Software Vendors are allowed to Copy or Distribute
|
||
my Products unless a Prior aggreement is arranged by Myself!
|
||
This is Copyrighted materials any and all Violators will be
|
||
Prosecuted By The Law! This is Being Distributed for HCS INC.
|
||
By Carl D. Henson.
|
||
|
||
Copyright (C) 1990-1991
|
||
Carl D. Henson |