174 lines
7.2 KiB
Plaintext
174 lines
7.2 KiB
Plaintext
|
||
|
||
=======================
|
||
AR-1000 Reset Procedure
|
||
=======================
|
||
|
||
|
||
* What you need :
|
||
|
||
- A small Philips screwdriver
|
||
- A soldering iron (30 W max)
|
||
|
||
* What to do :
|
||
|
||
- Remove the antenna
|
||
- Remove the batteries
|
||
- Remove the tuning, volume, and squelch buttons
|
||
- Remove the back cover (4 black screws), and disconnect it from
|
||
the rest
|
||
|
||
- Lay the unit flat on the table, keyboard and display below,
|
||
antenna connector away from you
|
||
- Unsolder the black wire from the lower right corner of
|
||
the upper board
|
||
- Unsolder the brown wire from the upper left corner of the same
|
||
board
|
||
- Remove the 3 screws that hold this board
|
||
- Pull GENTLY this board out of the upper panel (volume, squelch,
|
||
and tune rods come with the board - not the antenna connector)
|
||
|
||
- Unsolder the black wire from the upper left corner of the middle
|
||
board
|
||
- Unscrew the 3 copper columns that hold this board
|
||
|
||
- To get a better access on the lower board, you may wish to remove
|
||
some of the connectors that link the upper and middle boards to
|
||
the power supply board (the one that hides the speaker) --- don't
|
||
forget to take note of which connector goes where !!!
|
||
|
||
- Now take a look at the lower board. It looks like this :
|
||
|
||
|
||
(X) green led
|
||
|
||
+--------------------------------------------------------+
|
||
| |
|
||
| LCD display |
|
||
| |
|
||
+--------------------------------------------------------+
|
||
|
||
|
||
+-----------------+
|
||
| NEC |
|
||
| chip |
|
||
| D75308GF651 |
|
||
+-----------------+
|
||
|
||
|
||
o (A) o
|
||
| |
|
||
R1 R2
|
||
| |
|
||
o o
|
||
|
||
+---------------+ +--------+
|
||
| | | diodes |
|
||
| | +--------+
|
||
| |
|
||
| Hitachi chip | +--------+
|
||
| HN58C65FP-25T | | diodes |
|
||
| | +--------+
|
||
| |
|
||
| | +--------+
|
||
| | | diodes |
|
||
+---------------+ +--------+ (B)
|
||
|
||
|
||
- Solder a piece of wire (wrapping wire is a good candidate)
|
||
between points (A) and (B).
|
||
- Reconnect ALL wires (solder unsoldered wires and connect dis-
|
||
connected ones)
|
||
- Place batteries back
|
||
- Turn unit on : the display should be blank.
|
||
- Now type the following :
|
||
|
||
BANK
|
||
1 PROG 8 LIMIT 49.995 SEARCH 561.225 ENTER
|
||
2 PROG 50 LIMIT 107.995 SEARCH 561.225 ENTER
|
||
3 PROG 108 LIMIT 169.995 SEARCH 561.225 ENTER
|
||
4 PROG 170 LIMIT 296.995 SEARCH 561.225 ENTER
|
||
5 PROG 297 LIMIT 600 SEARCH 251.575 ENTER
|
||
6 PROG 805 LIMIT 1109995 [down arrow] 251.575 ENTER
|
||
7 PROG 1110 LIMIT 1300 [down arrow] 561.225 ENTER
|
||
|
||
- Turn unit off
|
||
- Unsolder the piece of wrapping wire
|
||
- Mount the unit back (wires, connectors, screws...)
|
||
|
||
- Turn unit on : it should be working !!!
|
||
|
||
* My comments :
|
||
|
||
DO NOT TRY THIS BY YOURSELF IF YOU DON'T FEEL CONFIDENT ABOUT
|
||
USING A SOLDERING IRON ON SUCH A MINIATURIZED DEVICE !!!
|
||
|
||
DON'T FORGET THAT, IF YOU FAIL, THE WARRANTY WILL BE VOID !!!
|
||
|
||
|
||
Now, let's relax. From the programming procedure, it is obvious
|
||
that you enter 7 sub-bands in the unit :
|
||
|
||
8 to 49.995 MHz
|
||
50 to 107.995 MHz
|
||
108 to 169.995 MHz
|
||
170 to 296.995 MHz
|
||
297 to 600.000 MHz
|
||
805 to 1109.995 MHz
|
||
1110 to 1300.000 MHz
|
||
|
||
These are the values for the AR-1000 as sold in France. The values
|
||
may be different for the units sold in Northern America (there may
|
||
be other gaps, especially for cellular phone frequencies).
|
||
|
||
I don't know what the following parameters (561.225 and 251.575)
|
||
mean. I guess they indicate which RF subcircuit, which step, and
|
||
which modulation mode to use. Anyway, since the sub-bands limits
|
||
appear so clearly, it might be fun to experiment. See what I mean ?
|
||
|
||
But, if we are to experiment, let's make things easier. Instead of
|
||
dismounting-soldering-programming-unsoldering-mounting the unit each
|
||
time, let's solder a 5" piece of wrapping wire to point (A),
|
||
a 5" piece of wrapping wire to point (B). Now we have 2 free ends :
|
||
let's solder a microswitch to them. We can glue the microswitch at
|
||
the bottom end of the unit, near the power supply board. Resetting
|
||
the AR-1000 is now much simpler : just open the unit (4 screws),
|
||
flip the switch, turn the unit on, reprogram it, turn it off, flip
|
||
the switch back, close the unit.
|
||
|
||
First of all, if you replace the first "8" with "0.5", you get an
|
||
AR-1000 with coverage extended down to 500 kHz. This may not work
|
||
on older units. My unit didn't let me program any frequency lower
|
||
than 0.5 MHz, or higher than 1300 MHz. Anyway, my aim was to try
|
||
to get rid of the 600-805 MHz gap. I tried the following sub-bands :
|
||
|
||
0.5 - 29.995
|
||
30.0 - 219.995
|
||
220.0 - 409.995
|
||
410.0 - 599.995
|
||
600.0 - 904.995
|
||
905.0 - 1209.995
|
||
1210.0 - 1300.000
|
||
|
||
To choose these values, I made the following assumptions : the
|
||
original values never exceed a 190 MHz span for the "561.225" series,
|
||
and never exceed a 304.995 MHz for the "251.575" series. I was careful
|
||
not to exceed these ranges, because of the necessarily limited span
|
||
of the internal VFO.
|
||
|
||
These values did seem to work, since I was able to hear some TV signals
|
||
near 620 MHz, that is, in the previous gap ! However, when I programmed
|
||
some search banks, it sometimes refused to search, even on "authorized"
|
||
frequencies (around 450 MHz). And, since there is nothing but TV
|
||
channels between 600 and 805 MHz (at least in France), I restored the
|
||
original values (except for the 0.5 MHz lower limit).
|
||
|
||
Now, if you find something interesting, please keep me informed !
|
||
|
||
|
||
Lionel ANCELET
|
||
|
||
BIX : lanc
|
||
CompuServe : 71641,1340
|
||
|