245 lines
12 KiB
Plaintext
245 lines
12 KiB
Plaintext
HIGH FREQUENCY ANTENNAS
|
||
|
||
JD DELANCY, K1ZAT/3
|
||
|
||
1. Long Wire Antennas:
|
||
|
||
a. The fundamental wire-type antenna is the horizontal half-
|
||
wave center-fed antenna. The nominal impedance of this type of
|
||
antenna is about 73 ohms, which will give a 1.5:1 standing wave
|
||
ratio (SWR) for a 50 ohm transmitter/receiver. Various matching
|
||
networks (delta and gamma types for example) can be used for 1:1
|
||
ratio, but the power loss with a 1.5:1 is minimal, and the value
|
||
of messing around with matching networks is questionable. Like
|
||
all balanced antennas, the dipole should be fed through a 1:1
|
||
balun (balanced to unbalanced transformer). The problem with
|
||
half-wave dipoles for 75 meter frequencies (3.9-4.0 Mhz) is that
|
||
the antenna is approximately 120 feet long. The antenna
|
||
should be erected horizontally as high as possible. In most
|
||
cases, the antenna will not be at least a 1/4 wavelength above
|
||
ground (at 75 meters that equates to 55 to 60 feet). This means
|
||
the directional effect of the dipole is virtually non-existant,
|
||
so any geographical orientation can be used for omni-directional
|
||
use. Dipoles are sometimes referred to as "long wire" antennas,
|
||
an erroneous term since a true long-wire is at least one
|
||
wavelength long. Variations of the half-wave dipole in use
|
||
includes the commonly called "coaxial" dipole, which uses coaxial
|
||
cable for part of the radiating element. The coaxial dipole
|
||
seems to have a better bandwidth, probably due to the diameter of
|
||
the coax used as a radiating element versus the number 14 or 12
|
||
wire diameter used with a regular dipole. The half-wave dipole
|
||
provides a good match only at the frequency for which it is "cut"
|
||
and it has a high angle of radiation (60-80 degrees) which is
|
||
correct for the 100-500 mile operating range.
|
||
|
||
b. The trap dipole is a variation of the half-wave
|
||
horizontal dipole which provides multi-band operation. Wave-trap
|
||
networks are inserted along the length of the dipole and act to
|
||
disconnect part of the antenna on higher bands to permit matching
|
||
at different frequencies. The characteristic impedance of the
|
||
trap dipole is also about 73 ohms, the same as the basic dipole.
|
||
The length of the antenna is still the same on the lowest band,
|
||
so a large amount of space is still required. The traps are
|
||
frequency-dependent networks, and thus provide a relatively
|
||
narrow bandwidth of matched operation. These antennas are also
|
||
non-directional at the heights normally used.
|
||
|
||
c. The inverted "V" dipole is a variation of the half-wave
|
||
dipole that can be used in restricted space. The center-fed
|
||
portion of the antenna is supported at a height of 40-50 feet,
|
||
and the radiating elements are ruin diagonally down to the
|
||
ground. The angle between the elements should be about 100
|
||
degrees for a good match to 50 ohms. The element lengths are
|
||
approximately the same as a regular dipole. The angle of
|
||
radiation is about 50 to 70 degrees which is suitable for
|
||
operation in the 100-500 mile range.
|
||
|
||
d. The rotatable dipole is a center-loaded dipole about 40
|
||
feet long with aluminum conduit elements. When mounted about 50
|
||
feet high, where the directional effect becomes apparent, it can
|
||
be rotated and permits desired signals to be peaked, or undesired
|
||
signals to be suppressed. Initial testing of such an antenna has
|
||
indicated no real advantage over a dipole or inverted "V" that
|
||
would make it worth the time and effort.
|
||
|
||
e. True long-wire antennas are at least one wave-length
|
||
long. Such antennas are directional off the ends of the antenna.
|
||
If one end of the long-wire is terminated in its characteristic
|
||
impedance (500-600 ohms), the antenna can be made uni-
|
||
directional, obviously, a good sized backyard is needed for a 75
|
||
meter long-wire antenna (it's at least 220 feet long!!).
|
||
|
||
2. Parasitic Arrays:
|
||
|
||
a. The "beam" antenna commonly used is a three-element
|
||
parasitic array - reflector, driven element, and director. The
|
||
antenna is directional and will give 3-5 DB gain. The elements
|
||
are half-wave in length, which means they are practical for 10,
|
||
15, and 20 meters -- get a little unwieldy for 40 meters -- and
|
||
just about impractical for 80 meters!! The characteristic
|
||
impedance is about 73 ohms, with most antennas having a gamma or
|
||
delta matching network for operation at 50 ohms.
|
||
|
||
b. The YAGI antenna is the "pure" form of the beam antenna.
|
||
YAGIs usually have 5 to 10 elements. The driven element in a
|
||
YAGI is a folded dipole, making the characteristic impedance
|
||
about 300 ohms. A 6:1 balun is normally used with YAGIs for a
|
||
match to 50 ohms. A ten element YAGI will have a gain of about
|
||
10 DB, with a narrow bandwidth. Again, the physical size of the
|
||
antenna with half-wave elements is the limiting factor in low-
|
||
frequency usage.
|
||
|
||
c. The Quad or delta-loop antenna has become popular in
|
||
recent years. the biggest advantage of Quad antennas is their
|
||
ability to provide gain with broad bandwidths. The gain of a
|
||
Quad is similar to that of a beam or YAGI (with an equal amount
|
||
of elements). The quad is a directional antenna with an
|
||
impedance of about 200 ohms (very approximate) and thus requires
|
||
a matching network for 50 ohm operation. Again, the limitation
|
||
in use for HF work is the physical size, since the Quad is a
|
||
square-shaped antenna with each side 1/4 wave length long, while
|
||
the delta-loop is triangular with each side 1/3 wave length long.
|
||
Needless to say, there are not many 80 meter Quads around.
|
||
|
||
3. Vertical antennas:
|
||
|
||
a. The most common vertical for fixed-station use is the
|
||
trap vertical, such as made by Hustler and Cushcraft. As with
|
||
the trap dipole, this antenna uses frequency dependent networks
|
||
to isolate portions of the antenna for proper resonating on
|
||
different bands. Although the antenna can be mounted at ground
|
||
level, greatly improved performance will result from installation
|
||
on top of a 20-30 foot high mast. The efficiency of the antenna
|
||
is dependent upon installation of adequate radials. At least
|
||
four, cut to 1/4 wave length, should be installed for each band.
|
||
These radials can also be used as the top guy wires for the mast.
|
||
These antennas can be adjusted for a very low SWR at 50 ohms, but
|
||
have a narrow bandwidth. The radiation angle is 30-40 degrees,
|
||
making them perform well for long-distance operation (1500 mile
|
||
range) while still usable for short-distance (500 mile range).
|
||
These are omni-directional antennas.
|
||
|
||
b. The single band vertical for 75 meter operation is
|
||
usually a loaded type, either with a coil at the bottom for base-
|
||
loading or a coil in the center of the mast for center loading.
|
||
While top-loading would be preferred, the size and weight of the
|
||
coil required would make for an unwieldy mechanical structure.
|
||
Center-loading is preferred to base-loading since a large portion
|
||
of the radiation is performed by the coil itself, and the
|
||
elevated coil will provide better performance and efficiency.
|
||
The antenna can be resonated for a 50 ohm impedance. Being
|
||
frequency-dependent, due to the loading coil, the bandwidth is
|
||
relatively narrow. Again, the efficiency of the antenna is
|
||
highly dependent upon the ground radial system. There should be
|
||
a minimum of four (1/4 wave) radials, with the more, the better.
|
||
The antenna can be elevated on a mast for better performance.
|
||
The radiation angle is similar to the trap vertical.
|
||
|
||
c. Towers utilized to elevate VHF antennas or beams can be
|
||
loaded and resonated as vertical antennas. The base of the
|
||
antenna can be grounded or insulated. Adequate ground radials
|
||
are required for proper operation. The radio amateur's handbook
|
||
shows several methods of feeding and matching towers for use as
|
||
vertical antennas, even for 160 meters. A common use for towers
|
||
is as a counterpoise for "half sloper" antennas. This is a form
|
||
of inverted-antenna with the tower acting as one of the radiating
|
||
elements. The antenna is fed at the top of the tower with the
|
||
coax shield connected to the tower, and the center conductor
|
||
connected to the sloping element. A "slope" of approximately 45
|
||
degrees will permit matching to 50 ohms.
|
||
|
||
d. Due to mechanical problems involved, the only practical
|
||
antenna for mobile HF operation is a vertical whip antenna.
|
||
These can be base-loaded, center-loaded, or trap verticals with
|
||
the body of the car acting as the counterpoise. The efficiency
|
||
of such an antenna, though, is only about 5 to 10 percent
|
||
(working DX from a car usually means driving to the top of Pike's
|
||
Peak!!). For local (100 mile) operation, the mobile vertical
|
||
whip does a good job. Two important considerations apply to
|
||
safety in mobile antenna operation -- one, the antenna must be
|
||
mechanically suitable to withstand the whipping and shaking
|
||
involved in traveling -- two, the antenna height must be
|
||
considered in clearing overhead obstructions, PARTICULARLY power
|
||
lines.
|
||
|
||
4. Examples of simple design antennas:
|
||
|
||
\ctr\G5RV MULTIBANDER ANTENNA
|
||
|
||
I I 51 FEET
|
||
I I
|
||
I I
|
||
I I
|
||
I I -------- 300 OHM LINE
|
||
I I L = 36 FT FOR
|
||
I I HORIZONTAL DIPOLES
|
||
I I
|
||
I I L = 29 FEET FOR
|
||
I I INVERTED VEE DIPOLES
|
||
I I
|
||
I I
|
||
I I
|
||
--------------
|
||
| | ----------1:1 50 OHM
|
||
| | BALUN
|
||
--------------
|
||
I
|
||
I
|
||
I -------------------50 OHM COAX
|
||
I (RG8) ANY
|
||
I LENGTH
|
||
XMTR/RCVR
|
||
|
||
The impedance at the lower end of the 300 ohm line is 50 to 60
|
||
ohms. A 1:1 balun is recommended for RFI or TVI suppression.
|
||
The antenna is slightly "short" on 80 meters and the 300 ohm line
|
||
section acts as a sort of matching stub on that band and acts as
|
||
an impedance transformer on the other bands. Trim the 300 ohm
|
||
line for best SWR on 15 or 20 meters (most critical bands). SWR
|
||
should be 2:1 or better across any band. SWR of 1.3:1 can be
|
||
obtained for the most resonant frequency in each band. Antenna
|
||
is good for about 400 watts. For higher power, use regular
|
||
amateur transmitting open-wire line (300 ohm). Shielded twin-
|
||
lead can be used, but length will be different due to cable
|
||
propagation factor. You will have to cut and try.
|
||
|
||
\ctr\DJ4BQ DOUBLE-DIPOLE
|
||
|
||
|
||
(55 feet) (55 feet)
|
||
------------------------------O O------------------------------
|
||
-----------------------O O-----------------------
|
||
(40.5 feet) I I (40.5 feet)
|
||
I I
|
||
I I --------200 OHM OPEN-WIRE
|
||
I I LINE, ANY LENGTH
|
||
I I
|
||
I I
|
||
------------
|
||
I I -------- 4:1 BALUN
|
||
I I (50:200 OHMS)
|
||
------------
|
||
I
|
||
I
|
||
I ------------- 50 OHM COAX
|
||
I (RG8) ANY LENGTH
|
||
I
|
||
I
|
||
XMTR/RCVR
|
||
|
||
This antenna operates from 80 to 10 meters. The longer dipole
|
||
operates on 80, 20, and 15 meter while the shorter dipole
|
||
operates on 40 and 10 meters. SWR of 1.2:1 to 1.5:1 are typical
|
||
on each band. This is a 200 ohm antenna and a 4:1 balun must be
|
||
used to match it to 50 ohm coax. Dipole wires should be spaced
|
||
at least six inches apart to eliminate interaction of dipoles.
|
||
Heavy-duty twin lead can be utilized for the dipoles (forming
|
||
both dipoles at the same time) but the length of the dipoles will
|
||
be different from the standard dimensions, and you will have to
|
||
"cut and try" for the lowest SWR. Amateur transmitting 200 ohm
|
||
open-wire line with plastic spacers should be used, with about a
|
||
six inch separation from tower legs or mast. Inverted Vee
|
||
operation may require shortening of the dipole lengths due to
|
||
extra capacity to ground.
|
||
\ff
|
||
|