120 lines
5.4 KiB
Plaintext
120 lines
5.4 KiB
Plaintext
|
||
Kingpin [RDT Syn.] presents:
|
||
|
||
---==== A CLOSER LOOK AT EPROMS ====---
|
||
|
||
A brief introduction to EPROMS, what they are used for, and how they work..
|
||
(Stolen from an undisclosed source..)
|
||
|
||
Whassup to Brian Oblivion and the rest of the RDT posse..
|
||
|
||
---=======================---
|
||
|
||
How an EPROM works:
|
||
|
||
With the advent of Large Scale Integration (LSI) and the decreasing
|
||
cost of semiconductors, the use of semiconductors as memory elements became
|
||
possible. Over the last few years, non-volatile semiconductor memory such as
|
||
the EPROM (Erasable Programmable Read-Only Memory) has become an increasingly
|
||
important part of microcomputer systems. Memory chips in general are carrying
|
||
enough bits to even challenge magnetic storage in many applications.
|
||
|
||
The EPROM is an important part of microcomputer memory and offers
|
||
many advantages over available memory devices. The EPROM is not a permanently
|
||
programmed device; rather it can be erased and then re-programmed when
|
||
changes are required. Also, the device configuration and fabrication
|
||
technique has allowed EPROMS to be cost effective for a variety of
|
||
applications. The heart of the EPROM'S flexibility is in the FAMOS
|
||
(floating-gate avalanche-injection metal oxide semiconductor) type transistor.
|
||
|
||
__________________________
|
||
/ Polysilicon Select Gate |\
|
||
__________/ ______________________ V \__________
|
||
| / ____________________ \ |
|
||
| SiO2 ___/ / __________________ \ \___ |
|
||
| |____/ |__________________| \____| |
|
||
| Polysilicon Floating Gate ^ |
|
||
|__________________________________________________|
|
||
|
||
Figure 1. FAMOS-Type EPROM
|
||
|
||
|
||
Programming the EPROM consist of storing instructions in the form of
|
||
electrical charges. By application of a sufficiently latge voltage to the
|
||
cells, electrons are injected into the floating silicon gate. Storage of the
|
||
charge is possible due to the high impedance of the floating gate structure.
|
||
The stored charge causes a shift in the cell threshold and switches the
|
||
transistor to a non-active state.
|
||
|
||
|
||
------ +25 Volts
|
||
|
|
||
____________|_____________
|
||
/ | \
|
||
__________/ __________|___________ \__________
|
||
| / ____________________ \ |
|
||
| SiO2 ___/ / __________________ \ \___ |
|
||
| |____/ |______e-__e-______| \____| |
|
||
| e- e- |
|
||
|__________________________________________________|
|
||
^^^^^^^^ Electrons stored
|
||
|
||
Figure 2. Programming an EPROM Cell
|
||
|
||
|
||
Because there are no electrical connections to the floating gate,
|
||
erasure must be achieved by a non-electrical process. The EPROM has a fused
|
||
quartz lid which permits the ultraviolet radiation to penetrate the cell. By
|
||
exposure of the polysilicon gate to UV radiation, the stored charge can be
|
||
drained as a result of photo excitation of the stored electrons. The excited
|
||
electrons then dissipate into the oxide layer reducing the floating gate
|
||
capacitance to its original, un-programmed state.
|
||
|
||
The EPROM is then ready to be reprogrammed.
|
||
|
||
|
||
UV Light __________________________ UV Light
|
||
\ / \ /
|
||
___\_______/ ______________________ \____/_____
|
||
| \ / ____________________ \ / |
|
||
| SiO2 ___/ / __________________ \ \___ / |
|
||
| \ |____/ |______e-__e-______| \____|/ |
|
||
| \____________e-_______e-__________/ |
|
||
|__________________________________________________|
|
||
| | | | Electrons exit
|
||
V V V V
|
||
|
||
Figure 3. Erasing an EPROM Cell
|
||
|
||
|
||
Calculating EPROM Erasure Times:
|
||
|
||
EPROM erasure is accomplished by a minimum dosage which is the total
|
||
amount of UV energy incident on the chip surface during a period of time.
|
||
EPROM manufacturers normally assign a nominal dose specification to their
|
||
devices to assist the user in determining proper erase times.
|
||
|
||
The minimum time required to erase an EPROM with a given dosage
|
||
specification can be calculated from the following equation:
|
||
|
||
Erase Time =
|
||
|
||
EPROM Dosage (W-sec/cm2) x 1000
|
||
-------------------------------
|
||
Intensity (uW/cm2)
|
||
|
||
Note that this equation is only valid for an EPROM that has been
|
||
calibrated with a source which has a spectrum equivalent to that of the light
|
||
source being used to erase the EPROM. Virtually all EPROM manufacturers use a
|
||
254nm source to calculate the dosage requirements for their EPROMS.
|
||
|
||
While most EPROM manufacturers' performance specifications ensure a
|
||
high quality, non-volatile memory device, the UV dose specified is typically
|
||
a dose sufficient to erase approximately 95% of all such devices. Due to
|
||
process variations in manufacuring, some 15 W-sec/cm2 EPROMS may require as
|
||
much as 40 W-sec/cm2. These variations do not normally reflect other aspects
|
||
of EPROM performance. Most EPROMS will erase well below the given dose
|
||
requirements.
|
||
|
||
---=======================---
|
||
|