81 lines
3.6 KiB
Plaintext
81 lines
3.6 KiB
Plaintext
|
|
|
|
[Ctrl-S Stop/Start] [Spacebar to Exit]
|
|
|
|
|
|
EXPLOSIVE PENS
|
|
|
|
Here are the instructions for building a device no agent should be
|
|
without. From the mind of "Q" himself, a device for your evaluation.
|
|
|
|
Materials......
|
|
|
|
[1]-(1) "Felt" Tip Pen
|
|
[2]-(1) "Ball" Point Pen
|
|
[3]-(1) High quality firecracker!
|
|
[4]-(1) 8 gram measure potassium parmagranite (optional)
|
|
[5]-(x) Scotch Tape
|
|
[6]-(1) Large Paper Clip
|
|
[7]-(2) Packages of matches
|
|
[8]-(1) Pair of scissors
|
|
[9]-(1) Length of Beige thread
|
|
|
|
Assembly......
|
|
|
|
[1]- Use thread to friction saw the felt tip pen in half at the point
|
|
where the cap "snaps" onto the pen. (about mid-section)
|
|
[2]- Remove the innerts of the felt tip pen, throw them away.
|
|
[3]- Pull the innerts out of a bic ball point pen and remove the ball
|
|
point assembly at the front of the pen.
|
|
[4]- Use scissors to widen the hole in the "felt" end of the pen. Insert
|
|
the ball assembly and make sure it is a tight fit. It should now
|
|
look as if the felt tip pen was constructed as a ball point pen.
|
|
[5]- Cut off abrasive strips from the packs of matches. It is best if they
|
|
have not been used. Tape these to the top of the firecracker near
|
|
the fuse, the strips should run parallel to the outstreached fuse.
|
|
Wrap fuse over the top of one strip and tape down so fuse runs parallel
|
|
to abrasive strips.
|
|
[6]- Unbend paperclip and tape a match to the metal rod, the match should
|
|
be parallel to the rod and it should be taped tight using as little
|
|
tape as possible.
|
|
[7]- Insert the match head 1/5 of the way between the abrasive strips
|
|
and wrap tape around the assembly. It should now look like this.
|
|
|
|
------______-----
|
|
[][][]a[][][]-----------------(b)
|
|
(())---------------------
|
|
______------_____ |(c)
|
|
|(d)
|
|
(a)-Explosive/(b)-Fuse/(c)-Match attached to metal rod/(d)-Abrasives
|
|
The entire assembly should be thin enough to slip into the case of
|
|
the felt tip pen.
|
|
[8]- Using scissors drill a small hole in the "non-tip" end of the felt
|
|
tip pen case. Insert the assembly so the metal rod fits through the
|
|
hole in the end of the pen case.
|
|
[9]- The assembly will not quite fit properly. The firecracker will
|
|
protrude from the cut half of the felt tip case. Slip the removed
|
|
end of the case over the firecracker. (join the halfs together over
|
|
the firecracker in the center) and mount the cap of the felt tip pen
|
|
on the end of the metal rod. Glue any loose parts. You are done!
|
|
|
|
To Detonate...
|
|
|
|
Simply hit the cap (mounted at end of pen permanently) and throw
|
|
it at your target, or hand it to your target. My favourite is to say
|
|
"Think Fast" and throw them your felt tip pen. (make it a easy throw)
|
|
Your victim will catch it, and it will then explode. Cutting off many
|
|
small appendages if you coat the firecracker with potassium parmagranite.
|
|
Or killing your target if you use contact poison in place of the potassium.
|
|
|
|
Theory of operation...
|
|
|
|
Quite simple, by hitting the cap you are ramming the match head at
|
|
the end of the metal rod between the tight abrasive strips causing
|
|
combustion. Or the "Orgasm" effect. (the term Axis Agents use!) The
|
|
fire lights the fuse and from there, the pen is history! (pardon the pun)
|
|
After hitting the cap you have a average time limit of 2.5 seconds to
|
|
rid yourself of the pen. (plenty of time actually...)
|
|
|
|
(>
|
|
|
|
[Ripco] Which 1-281 ?=menu,<CR>=abort: |