106 lines
3.0 KiB
Plaintext
106 lines
3.0 KiB
Plaintext
|
How to make an easily concealable bong from a Mag-Lite:
|
||
|
|
Written 2-21-02
|
||
|
|
|
||
|
|
You will will need a big mag lite and a few basic tools.
|
||
|
|
This bong looks exactly like a working Mag lite until you
|
||
|
|
remove the top. The bowl is under the top. The mouthpiece
|
||
|
|
is inserted into the switch hole, and the carb is opposite
|
||
|
|
the mouth piece and down about 2inches.
|
||
|
|
|
||
|
|
\____________/
|
||
|
|
\ /
|
||
|
|
\ / <-- Lens deal
|
||
|
|
\______/
|
||
|
|
|
||
|
|
|
||
|
|
| | <-- Bowl
|
||
|
|
__|_|__
|
||
|
|
| |
|
||
|
|
| |
|
||
|
|
| |
|
||
|
|
| |
|
||
|
|
| |
|
||
|
|
| |
|
||
|
|
| /
|
||
|
|
| | <--mouthpiece (switch) hole
|
||
|
|
| \
|
||
|
|
| |
|
||
|
|
| |
|
||
|
|
carb --> \ |
|
||
|
|
/ |
|
||
|
|
| |
|
||
|
|
| |
|
||
|
|
|||||||||
|
||
|
|
|||||||||
|
||
|
|
|||||||||
|
||
|
|
||||||||| <-- textured grip (great for striking matches)
|
||
|
|
|||||||||
|
||
|
|
|||||||||
|
||
|
|
|||||||||
|
||
|
|
|||||||||
|
||
|
|
|||||||||
|
||
|
|
|||||||||
|
||
|
|
|||||||||
|
||
|
|
|||||||||
|
||
|
|
|||||||||
|
||
|
|
|||||||||
|
||
|
|
|||||||||
|
||
|
|
|||||||||
|
||
|
|
| |
|
||
|
|
| |
|
||
|
|
| |
|
||
|
|
| |
|
||
|
|
| |
|
||
|
|
| |
|
||
|
|
|_______|
|
||
|
|
|_______| <-- end cap
|
||
|
|
|
||
|
|
|
||
|
|
materials:
|
||
|
|
1 mag lite
|
||
|
|
2 part epoxy
|
||
|
|
silicon sealent
|
||
|
|
legnth of bycicle brake cable
|
||
|
|
drill
|
||
|
|
1/2 metal pole
|
||
|
|
hammer
|
||
|
|
pliers
|
||
|
|
duct tape
|
||
|
|
half a brain
|
||
|
|
|
||
|
|
|
||
|
|
1. unscrew the end cap and the lens deal. unscrew the bulb retainer
|
||
|
|
and remove the bulb.
|
||
|
|
|
||
|
|
2. hammer on the bulb holder while pushing in the switch. use the
|
||
|
|
pole and the hammer to tap dwn the whole bulb holding switch thing
|
||
|
|
until it falles out the bottom of the mag-lite.
|
||
|
|
|
||
|
|
3. remove the rubber ring on the end cap and coat the threads with epoxy.
|
||
|
|
screw this bak on to the light
|
||
|
|
|
||
|
|
4. remove the spring from the switchnbulb assembly and also the small metal
|
||
|
|
cap and discard.remove the bulb holder from the assembly and invert
|
||
|
|
the cup. poke a bunch of small holes in the cup. coat the treads on
|
||
|
|
the bulb retainer with epoxy and screw onto the bulb holder. This is
|
||
|
|
the bowl. coat it in epoxy up to the line and push it back into the
|
||
|
|
assembly to the line. clean the excess epoxy.
|
||
|
|
|
||
|
|
5. remove the switch from the switchnbulb assembly. drill a 3/16" hole in the
|
||
|
|
bottom of the switchnbulb assembly and epoxy in the brake cable. cut
|
||
|
|
the cable so it will reach to the bottom of the mag.
|
||
|
|
|
||
|
|
6. coat the switchnbowl assembly in epoxy and putin to the mag like from the top.
|
||
|
|
the points up, stupid. tape any holes in the bowl and coat with the
|
||
|
|
silicone.
|
||
|
|
|
||
|
|
7. drill a hole opposite the switch hole and 2 inches down for the carb.
|
||
|
|
|
||
|
|
8. rip the reflector out of the lens deal and screw over the bowl.
|
||
|
|
|
||
|
|
9. make some kind of mothpiese to fit the switch hole. (this should be removeable)
|
||
|
|
|
||
|
|
10. fill it with water up to an inch below the carb. remove lens deal, insert
|
||
|
|
mouth piece. pack the bowl and have a smoke. (wait for the epoxy and shit
|
||
|
|
to dry)
|