108 lines
5.5 KiB
Plaintext
108 lines
5.5 KiB
Plaintext
|
***********************************************************
|
|||
|
|
*
|
|||
|
|
MEMBER NAME: LIGHT *
|
|||
|
|
*
|
|||
|
|
***********************************************************
|
|||
|
|
|
|||
|
|
|
|||
|
|
How To Make An In-Use Light
|
|||
|
|
From The Night Owl AE
|
|||
|
|
|
|||
|
|
|
|||
|
|
This file describes the operation and construction of a device that will
|
|||
|
|
signal whether or not an extension of a particular phone line is off-hook. It
|
|||
|
|
does NOT indicate whether or not a phone is being tapped, and will light
|
|||
|
|
whenever any extension is picked up.
|
|||
|
|
|
|||
|
|
The principle under which this device operates is that there is a voltage
|
|||
|
|
across the red and green wires of the phone line (the other wires are rarely
|
|||
|
|
used) that drops significantly when an extension is lifted. Though this
|
|||
|
|
voltage can be used to power a light on its own, the light would have to be of
|
|||
|
|
a very low power consumption in order not to keep the phone off-hook, and it
|
|||
|
|
would only light when the phone is on-hook.
|
|||
|
|
|
|||
|
|
A simple way to get around the above problem is to use a low current relay.
|
|||
|
|
Radio Shack sells some nice 12VDC SPDT relays that work well for this purpose.
|
|||
|
|
Don't buy the red relays or the subminis; though you want a low current
|
|||
|
|
coil, you also want the contacts to be able to handle a decent current.
|
|||
|
|
DPDT (double pole, double throw) will also work, you just won't use the
|
|||
|
|
other contacts.
|
|||
|
|
|
|||
|
|
For a 12 volt coil, the voltage will have to be dropped so that the relay
|
|||
|
|
will function properly. The proper resistance is around 10K ohms, but it is
|
|||
|
|
best to use a 5K ohm fixed resistor and a 10K ohm variable (standard values,
|
|||
|
|
any combination that can cover the 10K range will work fine). Adjust it to
|
|||
|
|
approximately 10K, or halfway for the combination above. Connect the
|
|||
|
|
resistors in series with the coil, and we'll adjust it later.
|
|||
|
|
|
|||
|
|
Due to the nature of this device (or rather, its simplicity) it will
|
|||
|
|
operate without having to be plugged into a phone, or vice versa. In other
|
|||
|
|
words, you can plug it directly into a jack anywhere, and it'll work.
|
|||
|
|
You'll want to get a modular plug that terminates in spade lugs for this
|
|||
|
|
purpose. Connect the green wire to one side of the coil, and the red to the
|
|||
|
|
resistors (so that it's all in series). If you don't have an extra phone
|
|||
|
|
jack, then you will want to a) buy a Y connector so that two phones can be
|
|||
|
|
plugged into the same jack, or b) get another phone jack and install it in
|
|||
|
|
the same box with the in-use light, so that you can plug a phone into it.
|
|||
|
|
Just connect the spade lugs to their respective colors.
|
|||
|
|
|
|||
|
|
For the light itself, you can use almost anything. Even a tiny light bulb
|
|||
|
|
and a battery will work fine, but after about 5 hours of phone use, you'll
|
|||
|
|
have to replace the battery. The best thing to use is a neon bulb powered
|
|||
|
|
by the 110V power available most places. Buy ones with dropping resistors,
|
|||
|
|
or use a 220K resistor for dropping. You should also get a panel lamp
|
|||
|
|
assembly to keep it steady and make it look pretty. Since the current is
|
|||
|
|
relatively low, you can use almost any power cord, or sacrifice an old
|
|||
|
|
extension cord. Connect it in series with the NC (normally closed) contacts
|
|||
|
|
of the relay (in series with the dropping resistor, of course).
|
|||
|
|
|
|||
|
|
Your circuits should now look like this:
|
|||
|
|
/
|
|||
|
|
--------RED----!---- 5k --- 10k -------O O-------------------!-----110V
|
|||
|
|
/ | |
|
|||
|
|
coil NC /
|
|||
|
|
| |
|
|||
|
|
-------GREEN---!-----------------------O O-- bulb --- 220k --!-----110V
|
|||
|
|
|
|||
|
|
Make sure that the phone circuit (left) and the lamp circuit (right) are
|
|||
|
|
totally 100% separate, and in no danger of touching. Use wire nuts for all
|
|||
|
|
connections in 110V that are not to a terminal post, and tape them. For all
|
|||
|
|
wires that are exposed, use electrical tape or shrink-wrap tubing to insulate
|
|||
|
|
them. Glue the relay to the box or mount it on a stable PC board.
|
|||
|
|
|
|||
|
|
If all looks well, hook it up. It should work immediately, but there are
|
|||
|
|
three things that can go wrong:
|
|||
|
|
|
|||
|
|
1) The relay keeps the phone off the hook. To remedy this, lower the
|
|||
|
|
resistance until it doesn't. If you can't lower the resistance enough,
|
|||
|
|
then you are using a resistor with a high current coil and you'll have to
|
|||
|
|
get one with a
|
|||
|
|
lower rating.
|
|||
|
|
|
|||
|
|
2) The relay won't close. The solution for this is the same as number 1.
|
|||
|
|
|
|||
|
|
3) The relay stays closed. Raise the resistance with the phone on hook until
|
|||
|
|
the light goes off.
|
|||
|
|
|
|||
|
|
When all is working, the lamp should be on when one or more extensions are
|
|||
|
|
off-hook, and will be off when all extensions are on-hook. It will blink when
|
|||
|
|
the phone rings.
|
|||
|
|
|
|||
|
|
This is a parts list:
|
|||
|
|
|
|||
|
|
1 box. Make it a nice one, preferably one with feet.
|
|||
|
|
1 phone cord with a modular plug at one end and spade lugs at the other.
|
|||
|
|
1 phone jack or Y adapter (optional).
|
|||
|
|
1 power cord or old extension cord.
|
|||
|
|
1 low current coil relay, double throw.
|
|||
|
|
1 5K fixed resistor.
|
|||
|
|
1 10K variable resistor.
|
|||
|
|
1 neon bulb with dropping resistor.
|
|||
|
|
1 panel lamp assembly. Some come with bulbs.
|
|||
|
|
|
|||
|
|
That's it. You may trade this file however you wish.
|
|||
|
|
|
|||
|
|
|
|||
|
|
|
|||
|
|
Downloaded From P-80 International Information Systems 304-744-2253
|