61 lines
2.4 KiB
Plaintext
61 lines
2.4 KiB
Plaintext
|
ASTROTEL 500, 580, 591
|
|||
|
|
|
|||
|
|
NOTES: This is a single NAM unit
|
|||
|
|
These units are manufactured by OKI and follow the same programming
|
|||
|
|
instructions as the 400 series OKI phones.
|
|||
|
|
The ESN prefix is 129 decimal, 81 hex.
|
|||
|
|
Astrotel: 213-869-4041
|
|||
|
|
|
|||
|
|
1. All phones should be initialized prior to programing, this will clear
|
|||
|
|
all user programing functions including memory and solve many units
|
|||
|
|
problems.
|
|||
|
|
|
|||
|
|
2. With the unit powered up press FUNC 9 9 * followed by the last 8 digits
|
|||
|
|
of the units decimal ESN. The handset will display "ALL CLEAR", press
|
|||
|
|
* to complete initialization.
|
|||
|
|
|
|||
|
|
3. Turn phone off then on again and within 10 seconds press END RCL FUNC
|
|||
|
|
CLR SEND. (Ignore the error tone after pressing FUNC).
|
|||
|
|
|
|||
|
|
4. The phone will display "Entr id", enter the access code 08693427.
|
|||
|
|
|
|||
|
|
5. If you have completed the above steps correctly the phone now displays
|
|||
|
|
the first programing entry.
|
|||
|
|
|
|||
|
|
6. # is used to store each step.
|
|||
|
|
|
|||
|
|
7. * is used to increment each step number.
|
|||
|
|
|
|||
|
|
8. CLR will revert display to previous data.
|
|||
|
|
|
|||
|
|
9. END is used to complete programing at any time.
|
|||
|
|
|
|||
|
|
PROGRAMING DATA:
|
|||
|
|
|
|||
|
|
STEP# #OF DIGITS/RANGE DISPLAY DESCRIPTION
|
|||
|
|
|
|||
|
|
01 10 DIGITS PHon MIN (AREA CODE & PHONE NUMBER)
|
|||
|
|
02 5 DIGITS Sid SYSTEM ID
|
|||
|
|
03 4 DIGITS iPCH IPCH AUTOMATICALLY SET
|
|||
|
|
04 2 DIGITS ACColC ACCESS OVERLOAD
|
|||
|
|
05 3 OR 4 DIGITS LoC Cod LOCK CODE
|
|||
|
|
06 2 DIGITS Gid GROUP ID (10 FOR USA)
|
|||
|
|
07 4 DIGITS Stn STATION CLASS MARK, USE 1000.
|
|||
|
|
08 4 DIGITS/0 OR 1 oPc bit OPTION BITS: (1 enables, from left to
|
|||
|
|
right):
|
|||
|
|
Horn Alert
|
|||
|
|
Hands Free
|
|||
|
|
Local Use
|
|||
|
|
MIN Mark
|
|||
|
|
|
|||
|
|
NOTE: The phone number and system ID can also be changed out of programing
|
|||
|
|
mode by using the following procedure.
|
|||
|
|
|
|||
|
|
1. Press FUNC 9 0 *
|
|||
|
|
2. Enter 3 or 4 digit lock code
|
|||
|
|
3. The existing phone number will be displayed
|
|||
|
|
4. Storing, incrementing and exiting follow the same methods as above.
|
|||
|
|
|
|||
|
|
LOCK: Press LOCK, UNLOCK: Enter three or four digit code.
|
|||
|
|
|
|||
|
|
SYSTEM SELECT: F 0 1 *, then RCL to scroll, then * to store desired option.
|