87 lines
3.7 KiB
Plaintext
87 lines
3.7 KiB
Plaintext
![]() |
|
|||
|
-----------
|
|||
|
:White Box:
|
|||
|
-----------
|
|||
|
Brought to you by Sirius Cybernetic's BBS
|
|||
|
|
|||
|
|
|||
|
This article will tell you how to change a normal touch tone keypad
|
|||
|
and convert it to a portable unit. In addition, we give the touch-tone
|
|||
|
frequencies.
|
|||
|
|
|||
|
First of all, the tones made by a touch tone telephone are not single
|
|||
|
tones, they are a combination of two tones, making "DTMF" (dual tone
|
|||
|
multi-frequency). The normal tone telephone dials 12 different signals, but
|
|||
|
is capable of dialing 16 different signals (see bulletin on silver boxes).
|
|||
|
|
|||
|
The power required by a keypad is about 25 volts, but they will work
|
|||
|
with as little as 15, thereby allowing the use of two 9- volt radio
|
|||
|
batteries. As you may have guessed, they are also designed to operate with
|
|||
|
a telephone type speaker (and phone line), and not the standard 8-ohm
|
|||
|
speaker which needs to be used for adequate volume. To accompolish this,
|
|||
|
we use a matching transformer, this is one of those miniature ones available
|
|||
|
at Radio Shack. Enough of the theory, now for the circuit.
|
|||
|
|
|||
|
You will need:
|
|||
|
|
|||
|
1. A touch tone keypad
|
|||
|
2. A miniature 1000 to 8 ohm transformer (Radio Shack # 273-1380)
|
|||
|
3. A standard 8-ohm speaker
|
|||
|
4. Two 9-volt radio batteries
|
|||
|
5. Two 9-volt battery clips
|
|||
|
6. A case to put it all in (optional)
|
|||
|
|
|||
|
A few construction notes, I suggest that you solder and tape all
|
|||
|
connections. It is also important to read this entire bulletin before
|
|||
|
attempting to construct this.
|
|||
|
|
|||
|
First, connect the RED wire of the transformer to either terminal on
|
|||
|
the speaker. Now connect the WHITE wire from the transformer to the other
|
|||
|
terminal on the speaker. Next, connect the RED (positive) wire of one
|
|||
|
battery clip to the black wire of the other battery clip. Now connect the
|
|||
|
the remaining RED wire on the second battery clip to the GREEN wire from the
|
|||
|
touch tone pad. Connect the BLUE wire from the touch tone pad to the
|
|||
|
ORANGE-and-BLACK striped wire from thetouch tone pad. To these two wires,
|
|||
|
now connect the remaining black lead from first battery clip. You have now
|
|||
|
finished the power connection to the keypad. Connect the BLACK wire keypad.
|
|||
|
Connect the BLACK wire from the keypad to the BLUE wire on the transformer.
|
|||
|
Next connect the RED-and-GREEN striped wire from the keypad to the GREEN wire
|
|||
|
on the transformer. The BLACK wire on the transformer should not be
|
|||
|
connected to anything, along with quite a few wires from the keypad. The
|
|||
|
connection of the keypad is now complete. All you have to do is connect two
|
|||
|
nine volt batteries to the battery clips, and you'll be ready to go. You may
|
|||
|
want tomount it in a case for easy portability. Note that the silver box
|
|||
|
modification CAN be made to this unit, allowing complete remote phreaking.
|
|||
|
|
|||
|
When none of the buttons are pressed, this unit uses NO power, thereby
|
|||
|
eliminating the need for a power switch, and extending the life of the
|
|||
|
batteries.
|
|||
|
|
|||
|
The following tones generated by each button on the keypad.
|
|||
|
|
|||
|
KEY FREQ. #1 FREQ. #2
|
|||
|
--- -------- --------
|
|||
|
1 697 1209
|
|||
|
2 697 1336
|
|||
|
3 697 1477
|
|||
|
A 697 1633
|
|||
|
|
|||
|
4 770 1209
|
|||
|
5 770 1336
|
|||
|
6 770 1477
|
|||
|
B 770 1633
|
|||
|
|
|||
|
7 852 1209
|
|||
|
8 852 1336
|
|||
|
9 852 1477
|
|||
|
C 852 1633
|
|||
|
|
|||
|
* 941 1209
|
|||
|
0 941 1336
|
|||
|
# 941 1477
|
|||
|
D 941 1633
|
|||
|
|
|||
|
All frequencies are measured in Hertz Note that A,B,C and D are not normally
|
|||
|
present (except for silver boxes)
|
|||
|
|
|||
|
|