92 lines
3.5 KiB
Plaintext
92 lines
3.5 KiB
Plaintext
|
|
|||
|
|
***********************************************************
|
|||
|
|
*
|
|||
|
|
MEMBER NAME: PORTSILB *
|
|||
|
|
*
|
|||
|
|
***********************************************************
|
|||
|
|
|
|||
|
|
***************************************
|
|||
|
|
* How to make a *
|
|||
|
|
* Portable Silver Box *
|
|||
|
|
* *
|
|||
|
|
* By: *
|
|||
|
|
* The *
|
|||
|
|
* Phone *
|
|||
|
|
* Phantom *
|
|||
|
|
* *
|
|||
|
|
***************************************
|
|||
|
|
|
|||
|
|
|
|||
|
|
This will tell you how to make a
|
|||
|
|
portable silver box out of:
|
|||
|
|
|
|||
|
|
A Radio Shack touch tone pad
|
|||
|
|
Some wire
|
|||
|
|
A Soldering iron
|
|||
|
|
And a SPDT switch
|
|||
|
|
|
|||
|
|
NOTE: You should have an I.Q. above room tempature before
|
|||
|
|
attempting this. Also, read all of this article before
|
|||
|
|
starting.
|
|||
|
|
|
|||
|
|
WARNING: This may be hazardous to your freedom.
|
|||
|
|
|
|||
|
|
1} Take off the plastic cover that stores the batteries and
|
|||
|
|
remove the screw that is in the center of the batteries. Now use
|
|||
|
|
a screw driver to pry open the box.
|
|||
|
|
2} Now you should have the two halves in your hands. On the side
|
|||
|
|
that has the circuit board, it should be held by two clips.
|
|||
|
|
Remove the circuit board now.
|
|||
|
|
|
|||
|
|
3} You should now be able to see the back side of the keypad.
|
|||
|
|
Connecting the the key pad and the circuit board is a ribben
|
|||
|
|
cable. With the ribben ends connected to the keypad away from
|
|||
|
|
you, count from the left over four wires. On the fourth wire,
|
|||
|
|
take and cut the plastic on either side on the wire. Then
|
|||
|
|
desolder it.
|
|||
|
|
|
|||
|
|
4} Now stare at the circuit board. Look at the connections of
|
|||
|
|
the chip. (SEE FIG.) There should be four pins not connected to
|
|||
|
|
anything. On the ninth pin (first row, first pin) solder a 3
|
|||
|
|
inch wire to it. The other end goes to the left side of the spdt
|
|||
|
|
switch.
|
|||
|
|
|
|||
|
|
5} Go back to the cable. Solder a 2 inch to the ribben cable you
|
|||
|
|
just took out. This is because it won't reach the switch. The
|
|||
|
|
other end goes to right side of the switch.
|
|||
|
|
|
|||
|
|
6} Now take a two inch wire and solder it to the hole that the
|
|||
|
|
cable came out of. Becareful not to get solder on the other
|
|||
|
|
wires. Now take the other end and solder it to the middle of the
|
|||
|
|
switch.
|
|||
|
|
|
|||
|
|
7} Make a hole in the top of the case to put the switch through.
|
|||
|
|
And put it back together.
|
|||
|
|
|
|||
|
|
THE FIGURE OF THE CHIP.
|
|||
|
|
|
|||
|
|
THE PIN >9< 10 11 12 13 14 15 16
|
|||
|
|
|
|||
|
|
1 2 3 4 5 6 7 8
|
|||
|
|
|
|||
|
|
(Pretty cool eh?)
|
|||
|
|
|
|||
|
|
_______________________________________
|
|||
|
|
|
|||
|
|
Switch the switch left according to the way you soldered it to
|
|||
|
|
make silver box tones on the 3,6,9, and # keys. Switch it to
|
|||
|
|
the right for a normal key pad. Switching it to the middle does
|
|||
|
|
NOTHING!!!!
|
|||
|
|
|
|||
|
|
This silver is small enough to fit in your pocket for phreaking
|
|||
|
|
at your nearest pay phone or where ever.
|
|||
|
|
|
|||
|
|
This file is for information only (RIGHT!) ha ha ha!
|
|||
|
|
|
|||
|
|
Written by:
|
|||
|
|
|
|||
|
|
The
|
|||
|
|
Phone
|
|||
|
|
Phantom
|
|||
|
|
|
|||
|
|
N
|