205 lines
8.2 KiB
Plaintext
205 lines
8.2 KiB
Plaintext
|
|
|||
|
|
------------------\
|
|||
|
|
Aqua Box |
|
|||
|
|
------------------|
|
|||
|
|
by |
|
|||
|
|
Game Warlord |
|
|||
|
|
Hyperspace Bandit |
|
|||
|
|
Frequency Bandit |
|
|||
|
|
Twilight Phantom |
|
|||
|
|
------------------/
|
|||
|
|
|
|||
|
|
|
|||
|
|
[Definitions]
|
|||
|
|
Black Box A device that tells the operator that the phone is hangup.
|
|||
|
|
When actually it is off the hook.
|
|||
|
|
Aqua Box A device that cancel F.B.I. lock and trace devices.
|
|||
|
|
Lock and Trace F.B.I. use a voltage transformer to keep the phone
|
|||
|
|
connection up. This allows them to trace with out being
|
|||
|
|
hangup on.
|
|||
|
|
|
|||
|
|
[General Infomation]
|
|||
|
|
-When phone is hangup the voltage is 55 volts.
|
|||
|
|
-When phone is off the hook the voltage is 5.5 volts.
|
|||
|
|
-Resistance over phone line is changing all the time.
|
|||
|
|
-Current is the same as resistance.
|
|||
|
|
-Phone line wires red and green are line1.
|
|||
|
|
-Phone line wires yellow and black are line2 (if you have a second line).
|
|||
|
|
|
|||
|
|
[Items needed]
|
|||
|
|
-T1 10:1 voltage ratio transformer
|
|||
|
|
-T2 1:10 voltage ratio transformer
|
|||
|
|
-LED Light Emiting Diode
|
|||
|
|
-SW1 DPDT Switch
|
|||
|
|
-SW2 DPDT Switch
|
|||
|
|
-Plug Molecular phone plug with cord (length as disere)
|
|||
|
|
-Jack Molecular phone jack
|
|||
|
|
-R1 10k Resistor(brown,black,orange,gold or silver)
|
|||
|
|
-R2 9.9k Resistor(white,white,red,gold or silver)
|
|||
|
|
-Perfboard 3 inches by 4 inches
|
|||
|
|
-Project box big enough to put the transformer, jack, swiches, ect.
|
|||
|
|
|
|||
|
|
[Equipment]
|
|||
|
|
-VOM meter
|
|||
|
|
-pliers
|
|||
|
|
-wirecutters
|
|||
|
|
-screwdrivers
|
|||
|
|
-soldering iron
|
|||
|
|
-drill
|
|||
|
|
-files
|
|||
|
|
-drillbits
|
|||
|
|
-solder
|
|||
|
|
-wire
|
|||
|
|
|
|||
|
|
[Circuit]
|
|||
|
|
|
|||
|
|
P |-red-----------------------------\
|
|||
|
|
l |-green------------------\ |
|
|||
|
|
u |-yellow-\not needed | |
|
|||
|
|
g |-black--/ | |
|
|||
|
|
/---------+--------+--------------------\
|
|||
|
|
J |-red----------+---------+----*---+--------------------+----\
|
|||
|
|
a |-green--------*-----1\_ | 1\_ | | |
|
|||
|
|
c |-yellow-\ | \O SW1 | \O | |
|
|||
|
|
k |-black--/not needed 2 2 | |
|
|||
|
|
| | | |
|
|||
|
|
| | | |
|
|||
|
|
O SW2 O | |
|
|||
|
|
/ / | |
|
|||
|
|
1 2 1 2 | |
|
|||
|
|
| | | | | |
|
|||
|
|
/----------------------/ \----+---+-----------------\ | |
|
|||
|
|
| /---------------------------/ \------------\ | | |
|
|||
|
|
| | | | | |
|
|||
|
|
| | /---------/ | | |
|
|||
|
|
| | | | | |
|
|||
|
|
| | *---- R1 -----* | |
|
|||
|
|
| | | | | |
|
|||
|
|
| | *-- LED - R2 --* | |
|
|||
|
|
| | | | | |
|
|||
|
|
| | \---------\ | | |
|
|||
|
|
| | | | | |
|
|||
|
|
| \----O O------------*-O O----/ | | |
|
|||
|
|
| T1 | T2 | | |
|
|||
|
|
\--------O O-*----------+-O O---------/ | |
|
|||
|
|
| | | |
|
|||
|
|
| \--------------------------/ |
|
|||
|
|
\------------------------------------------/
|
|||
|
|
|
|||
|
|
|
|||
|
|
[Construction]
|
|||
|
|
-Take the Molecular phone plug(Plug) with cord. The cord length
|
|||
|
|
is if you want it next to the wall, phone, modem, ect. First,
|
|||
|
|
remove about an inch and a half of insulation off with the
|
|||
|
|
wirecutters. Second, tie off the yellow and black wires. They are
|
|||
|
|
not needed. Third, take off about three forths of insulation off
|
|||
|
|
the red and green wires. Then twist the wires, but not together.
|
|||
|
|
Then melt some solder on the wires. Forth, drill a forth of and
|
|||
|
|
inch hole in one end of the project box. Fifth, put the wires
|
|||
|
|
through the hole about three inches, and tie the cord so that
|
|||
|
|
the wires will not slip.
|
|||
|
|
|
|||
|
|
+-----------------------+
|
|||
|
|
| red |
|
|||
|
|
hole | / |
|
|||
|
|
Plug \ = /\green |
|
|||
|
|
]-----------------------------*< |
|
|||
|
|
=| \__yellow\ |
|
|||
|
|
|\ \-black--* |
|
|||
|
|
| knots-----/ |
|
|||
|
|
+-----------------------+
|
|||
|
|
|
|||
|
|
-Drill a hole on top. Then file it. So that SW1 will fit
|
|||
|
|
correctly. Insert SW1. Make sure the it is sercure. Next,
|
|||
|
|
solder the red and green wires to the middle termals of the
|
|||
|
|
SW1 on seprate sides.
|
|||
|
|
|
|||
|
|
SW1 +--------+
|
|||
|
|
|O p1 O|
|
|||
|
|
| |
|
|||
|
|
red-O O-green
|
|||
|
|
| |
|
|||
|
|
|O p2 O|
|
|||
|
|
+--------+
|
|||
|
|
|
|||
|
|
-Drill a hole and file, so that the Jack will fit. Insert Jack.
|
|||
|
|
First, cut two wires three inches long. Second, take off about
|
|||
|
|
three forths of a inch of insulation on both ends of both
|
|||
|
|
wires. Third, put some solder on the ends of the wires. Forth,
|
|||
|
|
solder one wire on each p1 on SW1. The side where the red wire
|
|||
|
|
is, solder the other end of the wire on p1 of SW1 to red on
|
|||
|
|
the Jack. The side where the green wire is, solder the other
|
|||
|
|
end of the wire on p1 of SW1 to green on the Jack. Sixth, cut
|
|||
|
|
two more wires about five inches long. Seventh, take off about
|
|||
|
|
three forths of a inch of insulation on both end of both wires.
|
|||
|
|
Eighth, put some solder on the ends of the wires. Nineth,
|
|||
|
|
solder one wire on p1 of SW1.
|
|||
|
|
-Drill another hole on the top. File it, so that SW2 fits.
|
|||
|
|
Insert SW2. First, cut two wires about two and a half inches
|
|||
|
|
long. Second, take off about three forths of a inch of
|
|||
|
|
insulation on both ends of both wires. Third, put some solder on
|
|||
|
|
the ends of the wires. Forth, solder one wire on each p2 on SW1.
|
|||
|
|
Fifth, solder the other end of wires to the middle termal of
|
|||
|
|
SW2. Sixth, cut four wire about three inches long. Seventh, take
|
|||
|
|
off about three forths of a inch of insulation on both ends of
|
|||
|
|
the wires. Eighth, put so solder on each end of the wires.
|
|||
|
|
Nineth, solder one wire on each termal p1 and p2 of SW2.
|
|||
|
|
-Drill a hole on top, so that the LED fits. Cut a wire about
|
|||
|
|
three inches,remove insulation,and solder to LED leg. On the
|
|||
|
|
other leg solder R2.
|
|||
|
|
-Take the perfboard. Insert T1. Connect wires from one side of
|
|||
|
|
sw2 to the termals on one side of T1. Cut two wires about two
|
|||
|
|
inches, remove insulation, solder to the other termals of T1.
|
|||
|
|
Next, solder ends of wires to the termals on one side of T2.
|
|||
|
|
Cut two wires about two inches, remove insulation, solder to
|
|||
|
|
each end of R1, also solder the LED and R2 to each end of R1.
|
|||
|
|
Finaly, solder the wires from the other side of SW2 to each side
|
|||
|
|
of R1.
|
|||
|
|
|
|||
|
|
--O O---*-O O---*-------------
|
|||
|
|
SW2 T1 Jack T2 *---O SW2
|
|||
|
|
--O O---*-O O-\ | LED
|
|||
|
|
|R1 R2
|
|||
|
|
\-*---O---------
|
|||
|
|
|
|||
|
|
note-----
|
|||
|
|
T1 and T2 are the same type transformer just revesed, the
|
|||
|
|
voltage ratio is primary voltage/ secondary voltage.
|
|||
|
|
|
|||
|
|
1 3-----*-3 1
|
|||
|
|
|
|||
|
|
T1 Jack T2
|
|||
|
|
|
|||
|
|
2 4-----*-4 2
|
|||
|
|
|
|||
|
|
-Put project box together
|
|||
|
|
|
|||
|
|
+---------------------------------------+
|
|||
|
|
| SW1 SW2 LED |
|
|||
|
|
| 1 O 2 1 O 2 O |
|
|||
|
|
]-Plug---| [Jack
|
|||
|
|
| |
|
|||
|
|
| |
|
|||
|
|
+---------------------------------------+
|
|||
|
|
|
|||
|
|
note --- please mark your switches and positions. it will help.
|
|||
|
|
|
|||
|
|
[How to Use It]
|
|||
|
|
-SW1 is off/on,SW2 is black/aqua.
|
|||
|
|
-First, SW1 is 1, SW2 is 1. Second, turn on, the black box is on
|
|||
|
|
,and you call as mention in definition. Third, when finish
|
|||
|
|
change SW2 to 2, if LED comes on then F.B.I. is trying to trace
|
|||
|
|
,but the aqua box is on and hangsup your phone.
|
|||
|
|
|
|||
|
|
|
|||
|
|
[Comments]
|
|||
|
|
This is experimental.
|
|||
|
|
|
|||
|
|
We would like some response, or ideas, or anything else.
|
|||
|
|
If you meet us on a board, just say 'hi, i liked that black and
|
|||
|
|
aqua box of yours.'
|
|||
|
|
|
|||
|
|
|
|||
|
|
|
|||
|
|
|
|||
|
|
|